Panasonic SC-CH350 User Manual
Panasonic, Ììimììiwf*^0, Sc-ch350
Table of contents
Document Outline
- Table of Contents
- Caution for AC mains iead
- Suggestions for Safety
- ■ Use a standard AC wall outlet
- ■ Grasp the plug when disconnecting the power supply cord
- ■ Place the unit where it will be well ventilated
- ■ Be sure to place the unit on a fiat, level surface.
- ■ Never attempt to repair nor reconstruct this unit
- ■ Take particular care if children are present
- ■ If water is spilled on the unit
- ■ Avoid spray-type insecticides
- ■ Never use alcohol or paint thinner
- ■ Disconnect the power supply cord if the unit will not be used for a long time
- ■ If trouble occurs
- Before Use
- Concerning the Remote Control
- I Battery installation
- Use of batteries
- Operation notes
- Supplied accessories
- stacking the components
- Connections
- LUOKAN 1 LASERLAITE KLASS1 LASER APPARAT
- 1 Connect the FM indoor antenna.
- 2 Connect the LW/MW loop antenna.
- Connect the AC power supply cord after you have connected all other cables and cords.
- M Optional antenna connections FM outdoor antenna (not included)
- LW/MW outdoor antenna (not included)
- ■ External unit connection Analog player
- Surround speakers
- ■ “REC OUT" terminal
- Tuner section
- Display section
- Amplifier section
- Display section
- Cassette deck section
- Compact disc player section
- Memory presetting
- 1 Press the band-select button to select FM, LW or MW.
- 2 Press TUNING to select the MANUAL tuning mode.
- 0Tune In your favorite station using the jog dial.
- @ Press SET.
- Repeat steps 3 through 4 to memorize a station in each of the remaining preset channels.
- ■ From the main unit
- 1 Press the band-select button to select FM, LW or MW.
- 2 Press TUNING to select PRESET.
- 3 Turn the jog dial to select the desired preset channel number.
- S If noise is excessive in the FM mode Press FM MODE/B.P to monaural position.
- ■ From the remote control
- 1 Press TUNER/BAND to select FM, LW or MW.
- 2 Press the numeric button corresponding to the preset channel you wish to tune in.
- Sequential play
- Program play
- ■ From the main unit
- 1 Press the CD input select button.
- 2 0Turn the jog dial to select the track you
- 0 Press SET.
- 4 Press the CD play button.
- ■ Program memory function
- Repeat step 2 for each track you wish to program in sequence.
- ■ From the remote control
- 1 Press the CD input select button.
- 2 Press PROGRAM.
- 3 Press the numeric buttons to select the track numbers.
- 4 Repeat step 3 until you have completed the program.
- 5 Press the CD play button.
- Program play (continued)
- Direct access play
- Special features
- To play back prerecorded cassettes
- Listening to two tapes consecutively
- To fast forward or rewind the tape
- To record from the radio or external source
- Switch on the power.
- 1 Press the deck 2 eject button to load a cassette in deck 2.
- 3 Press REVERSE MODE to select the reverse mode you want to use.
- ■ When you record from the compact discs
- After pressing REC PAUSE;
- ■ To briefly interrupt recording
- Press REC PAUSE.
- ■ To stop recording
- Press the cassette deck stop button.
- ■ To erase a recorded tape (Deck 2)
- ■ To record with desired tone
- ■ To use the beat proof function Press FM MODE/B.P on the tuner section.
- Sequential CD recording (ALBUM)
- Switch on the power.
- 1 Press the CD input select button.
- 2 Press OPEN/CLOSE on the CD player to load a disc.
- 3 Press CD EDIT.
- 4 0Turn the jog dial to select ALBUM.
- 5 Load a cassette in deck 2.
- 6 Press DOLBY NR when making a Dolby NR recording.
- 7 Press REVERSE MODE to select the “ "
- 8 0 Turn the jog dial to specify the length of the
- Press SET.
- 9 Press the CD play button for automatic recording.
- ■ About Automatic Tape Level Setting (ATLS)
- Press the CD stop button twice.
- ■ To record with straight sound tone
- ■ To record with desired tone
- (continued)
- Tape length priority recording (FIT)
- 1 Press the deck 2 eject button to load a cassette in deck 2.
- 2 Press DOLBY NR when making a Dolby NR recording.
- 3 Press REVERSE MODE to select the “ ”
- 4 Press the CD input select button.
- 5 Press OPEN/CLOSE on the CD player to load a disc.
- 6 Press CD EDIT.
- 7 0 Turn the jog dial to select FIT.
- (D Press SET.
- Press the CD stop button twice.
- You can confirm the play sequence on the display by pressing the skip/search button in the stop mode.
- (continued)
- Program edit-recording (PROGRAM)
- 1 Press the deck 2 eject button to load a cassette in deck 2.
- 2 Press DOLBY NR when making a Dolby NR recording.
- 4 Press the CD input select button.
- 5 Press OPEN/CLOSE on the CD player to load a disc.
- 6 Press CD EDIT.
- 7 (T) Turn the jog dial to select PROGRAM.
- 8 0 Turn the jog dial to select the length of the tape you are using.
- ■ To confirm the play sequence
- You can confirm the play sequence on the display by pressing the skip/search button in the stop mode.
- (continued)
- To record from another disc on the remaining blank portion of the tape (LINK)
- 1 Press OPEN/CLOSE to replace the disc.
- 2 Press CD EDIT.
- 0Turn the jog dial to select the desired editing mode.
- Press SET.
- 4 Press the CD play button for automatic recording.
- 5 If you record from more discs, follow the above procedure.
- ■ To cancel the link-edit recording
- Press the stop button in the deck section.
- 1 Press the TAPE input select button.
- 3 Select the desired reverse mode.
- Press one of the one
- ■ To stop the tape-to-tape-recording
- ■ To record another tape on the remaining blank tape
- Changing the Tone
- To retrieve the equalization curves preprogrammed to this system
- About equalization curves preprogrammed to this unit
- To change the equalization curve continuously (Demonstration function)
- To store a desired equalization curves (USER curve)
- 1 Press -EQ MODE-FIXED/USER momentarily to seiect the desired equaiization curve.
- Press one of EQ LEVEL to adjust the equalization effect.
- While playing the desired source. Press SURROUND to ON.
- ■ To cancel the SURROUND effect Press SURROUND once again.
- 1 Press CLOCK/TIMER.
- 2 0 Turn the jog dial to select P-TIMER.
- 0 Turn the jog dial to select the hour you wish timer play to begin. In this case, set it on 7.
- (D Press SET.
- 0 Press VOL. PRESET to set the volume level for timer play.
- (2) Adjust the volume level using the volume level control.
- (3) Press VOL. PRESET again.
- 6 Press one of the input select buttons.
- 7 Press PLAY TIMER.
- ■ When you have made a wrong setting on steps 1 to 4 (on page 50)
- Press CANCEL.
- Press CLOCK/TiMER in the power standby mode.
- ■ To cancei timer piay Press PLAY TiMER.
- ■ To change the timer setting
- ■ To change the source oniy
- ■ To use the play timer everyday
- Switch on the power.
- 1 Press CLOCK/TIMER.
- 2 0 Turn the jog dial to select R-TIMER.
- 0 Press SET.
- 0 Press SET.
- 0 Press SET.
- Press SET.
- 5 Press the TUNER input select button and tune in the station whose broadcast you want to record.
- ■ To confirm timer recording
- ■ To cancel timer recording Press REC TIMER.
- ■ To change the timer setting
- ■ To change the source only
- ■ To stop the timer recording on the way
- To use the sleep timer
- Enjoying the Microphone Mixing
- Using an External Unit
- Care & Use