Rice Lake 420 Plus HMI Digital Weight Indicator Installation Manual User Manual
420 plus, Installation manual
Table of contents
Document Outline
- Contents
- About This Manual
- Safety
- 1.0 Introduction
- 1.1 Operating Modes
- 1.2 Front Panel Keypad
- 1.3 LED Annunciators
- 1.4 Indicator Operations
- 1.4.1 Toggle Gross/Net Mode/Piece Count
- 1.4.2 Toggle Units
- 1.4.3 Zero Scale
- 1.4.4 Acquire Tare
- 1.4.5 Enter Tare (Keyed Tare)
- 1.4.6 Remove Stored Tare Value
- 1.4.7 Acquire Parts Sample
- 1.4.8 Display Part Weight
- 1.4.9 Display Accumulator
- 1.4.10 Display or Change Time
- 1.4.11 Display or Change Setpoint Value
- 1.4.12 Turn Setpoint On or Off
- 1.4.13 Print Ticket
- 1.4.14 Enter New ID
- 2.0 Installation
- 2.1 Unpacking and Assembly
- 2.2 Enclosure Disassembly
- 2.3 Cable Connections
- 2.3.1 Cable Grounding
- 2.3.2 Bypass Power Button
- 2.3.3 DC Power Wiring Guidelines
- 2.3.4 Load Cells
- 2.3.5 Serial Communications
- 2.3.6 Digital I/O
- 2.3.7 Analog Output
- 2.4 Analog Output Module Installation
- 2.5 Enclosure Reassembly
- 2.6 Board Removal
- 2.7 Replacement Parts
- 3.0 Configuration
- 3.1 Configuration Methods
- 3.1.1 Revolution Configuration
- 3.1.2 EDP Command Configuration
- 3.1.3 Front Panel Configuration
- 3.2 Menu Structures and Parameter Descriptions
- 3.2.1 Configuration Menu
- 3.2.2 Format Menu
- 3.2.3 Calibration Menu
- 3.2.4 Serial Menu
- 3.2.5 Program Menu
- 3.2.6 Print Format Menu
- 3.2.7 Setpoint Menu
- 3.2.8 Digital Input Menu
- 3.2.9 Analog Output Menu
- 3.2.10 Version Menu
- 4.0 Calibration
- 5.0 EDP Commands
- 5.1 The EDP Command Set
- 5.1.1 Key Press Commands
- 5.1.2 Reporting Commands
- 5.1.3 The RESETCONFIGURATION Command
- 5.1.4 Parameter Setting Commands
- 5.1.5 Soft Reset
- 5.1.6 Normal Mode Commands
- 5.2 Saving and Transferring Data
- 5.2.1 Saving Indicator Data to a Personal Computer
- 5.2.2 Downloading Configuration Data from PC to Indicator
- 6.0 Print Formatting
- 7.0 Appendix
- 7.1 Error Messages
- 7.1.1 Displayed Error Messages
- 7.1.2 Using the XE EDP Command
- 7.2 Status Messages
- 7.2.1 Using the P EDP Command
- 7.2.2 Using the ZZ EDP Command
- 7.3 Continuous Output (Stream) Format
- 7.4 ASCII Character Chart
- 7.5 Front Panel Display Characters
- 7.6 Conversion Factors for Secondary Units
- 7.7 Digital Filtering
- 7.7.1 DIGFLx Parameters
- 7.7.2 DFSENS and DFTHRH Parameters
- 7.7.3 Setting the Digital Filter Parameters
- 7.8 Analog Output Calibration
- 7.9 Test Mode
- 7.10 Regulatory Mode Functions
- 7.11 LED Functions
- 7.12 Specifications
- 420 Plus Limited Warranty