Losi LOSB9593 - Manual

EN EN
NOTICE
All instructions, warranties and other collateral
documents are subject to change at the sole
discretion of Horizon Hobby, Inc. For up-to-date
product literature, visit www.horizonhobby.com
and click on the support tab for this product.
MEaNINg Of SpECIal laNguagE
The following terms are used throughout the
product literature to indicate various levels of
potential harm when operating this product:
NOTICE: Procedures, which if not properly
followed, create a possibility of physical property
damage AND little or no possibility of injury.
CauTION: Procedures, which if not properly
followed, create the probability of physical
property damage AND a possibility of
serious injury.
WaRNINg: Procedures, which if not properly
followed, create the probability of property
damage, collateral damage, and serious injury
OR create a high probability of superficial injury.
WaRNINg: Read the ENTIRE instruction
manual to become familiar with the features of
the product before operating. Failure to operate
the product correctly can result in damage to the
product, personal property and cause serious
injury.
This is a sophisticated hobby product and NOT a toy.
It must be operated with caution and common sense
and requires some basic mechanical ability. Failure
to operate this Product in a safe and responsible
manner could result in injury or damage to the
product or other property. This product is not
intended for use by children without direct adult
supervision. Do not attempt disassembly, use with
incompatible components or augment product in any
way without the approval of Horizon Hobby, Inc. This
manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all
the instructions and warnings in the manual, prior to
assembly, setup or use, in order to operate correctly
and avoid damage or serious injury.
Age Recommendation
Not for Children under 14 years.
This is not a toy.
Overview
The 2-in-1 MRX50-BL Electronic Speed Controller
and Spektrum™ 2.4GHz Receiver unit is designed
to convert the Losi ® Micro RTRs (1/24- and 1/36-
scale) to Brushless and 2.4GHz. The MRX50-BL will
provide fantastic Brushed or Brushless performance,
improved range, and interference-free operation.
When run in Brushless Mode, the power, efficiency,
torque and reliability will all increase dramatically.
Included
1 MRX50-BL ESC
4 M1.6 x 6 Screws
3 M1.6 x 4 Screws
2 Motor Screws
1 Wire Adapter (3-wire to 2-wire)
1 Micro 1/24 Chassis Top Cover for MRX50-BL
Safety Precautions
• The motor and ESC will be hot during and after
operation. Do not touch.
• Running a 3S (11.1-volt) LiPo battery with a brushed
Motor will cause damage to the motor and/or ESC
and will not be covered by warranty.
• Brushless Motor Only: Attempting to remove the
pinion will cause damage to the motor and will
void the warranty.
Features
• Compatibility with all Spektrum surface transmitters
• A brushless-ready design—just install a brushless
motor and enjoy the extra power and improved
motor life
• Direct fit replacements for the stock ESC/Receiver,
requiring no modifications or additional components
• Compatibility with Losi 5-wire and 3-wire servos
• 2S–3S LiPo and NiMH battery compatibility with
Auto Cut-Off
3S (11.1-volt) LiPo batteries to be used with
Brushless Motor Only
• Forward, Brake and Reverse Drive Profiles
• Included micro 3-Wire to Micro 2-Wire Plug for easy
brushed or brushless operation
• Powerful 8750KV motor for superior reliability
and extreme power, torque and top speed
• A 12T metal pinion for long life and
improved reliability
Specifications
MRX50-BL
Motor Type Brushless Sensorless
Brushed (Auto Detect)
Low Voltage Cutoff 2S and 3S LiPo
Auto Battery
Type Detection Yes
Input Voltage 4-cell (4.8-volt) NiMH/NiCd
Brushed or 2S (7.4-volt) Not 3S
Compatible
Input Voltage 4-cell (4.8-volt) NiMH/NiCd or
Brushless 2S (7.4-volt) to 3S (11.1-volt) LiPo
Continuous 5A (20A)
(Peak) Current
Full On Resistance
.063 Ohm
Motor Limit 10250KV
Motor
Connector Type Micro 3-Wire
Battery
Connector Type Micro 2-Wire
Dimensions 42mm x 31mm x 8.5mm
(1.64 in x 1.228 in x 0.33 in)
Weight (with wires) 8.4 g (1.92 oz)
BEC Output
5.0V/1.0A
Signal Type DSM
Signal Band 2.4GHz
Battery 2-Wire Connector
OFF
ON
Switch
Motor 3-Wire
Connector
Bind
Button
3-Wire Servo Plug
5-Wire Servo Plug
LOSB9470 8750KV
Motor Type Sensorless
Input Voltage 4-cell (4.8-volt) NiMH/NiCd or
2S (7.4-volt) to 3S (11.1-volt) LiPo
Dimensions Can Diameter: 12.0mm (0.47 in)
Can Length: 22.1mm (0.87 in)
Shaft Diameter: 1.5mm (0.06 in)
Shaft Length: 7.6mm (0.30 in)
Weight 9.0 g (0.32 oz)
(with wires/pinion)
Motor
Micro 3-Wire
Connector Type
MRX50-BL Installation
When installing the MRX50-BL into a Losi 1/24 Micro, use
the included Chassis Top Cover to replace the Top Cover
provided with the RTR.
1. Remove the Chassis Top Cover as shown in the
specific vehicle instruction manual.
2. Unplug the wire connectors from the servo, motor,
and battery.
3. Use a small screwdriver to push back gently on the
rear locking tab to remove the ESC/Receiver switch
from the chassis.
4. Remove all 4 screws that secure the original ESC/
Receiver unit to the mounting surfaces.
5. Remove the original ESC/Receiver unit.
6. Remove the stock brushed motor as shown in the
specific vehicle instruction manual.
7. Install the LOSB9470 8750KV Brushless Motor with
12T Pinion to the motor mount using the included
motor screws. Install the motor mount into the
vehicle and properly set the gear mesh as shown
in the specific vehicle instruction manual.
NOTICE: Do not use screws longer than 4mm
to install the Brushless motor or you may damage
the inside of the motor.
8. Start installation of the MRX50-BL by pressing
the switch into the chassis between the front
and rear switch mounting tabs. Be sure to have
the two switch posts with wires attached toward
the “ON” marking on the chassis to ensure the
On/Off function of the ESC/Receiver is correct to
the marking on the chassis.
9. For Brushed Motor operation, connect the
Brushed Motor’s Micro 2-Wire connector to
the 2-Wire side of the adapter; then connect
the 3-Wire side of the adapter to the MRX50-
BL Micro 3-Wire connector; the connectors are
designed to only connect one way. For Brushless
Motor operation, connect the Brushless Motor’s
Micro 3-Wire connector to the Micro 3-Wire
connector of the MRX50-BL; the connectors
are designed to only connect one way.
10. Pull the 2-Wire battery connector toward the
rear of the chassis, and guide it though the open
slot in the chassis into the battery compartment.
11. For the Micro 1/24 vehicles, guide the gray
antenna wire through the small hole in the rear
of the included Brushless Micro 1/24 Top Cover.
Also, guide the servo plug and wire through the
opening in the Micro 1/24 Top Cover directly
behind the servo and pull through. Then secure
the cover to the chassis as shown in the specific
vehicle instruction manual.
For all other Micros vehicles, guide the gray
antenna wire through the small hole in the
rear of the ESC/Receiver unit cover, and
reinstall as instructed in the specific vehicle
instruction manual.
12. Plug the servo wire into the appropriate location.
Connect the 5-wire servo plug to the 5-wire
input or the 3-wire servo plug to the 3-wire
input noting proper orientation (the signal
wire is towards the front of the chassis).
Connecting the Battery
Use a Losi Micro 4-cell (4.8-volt) NiMH battery pack
or a 2S-3S (7.4-11.1-volt) LiPo pack.
NOTICE: Do not use 3S (11.1-volt) LiPo
batteries with brushed motors.
1. Move the on/off switch to the “off” position.
2. Connect a fully charged battery pack to the
battery connector of the ESC/Receiver.
Adjusting the Transmitter
Adjust the transmitter prior to powering on the
MRX50-BL ESC.
1. Set the “throttle reversing” setting to the
NORMAL position.
2. Set “throttle trim” to the CENTER or ZERO
position.
3. Set throttle “end point adjustment (EPA)”
to 100% in each direction.
CAUTION: Always power on the
transmitter before the receiver. Always
power off the receiver before the transmitter.
LOSB9593 Micro 2.4GHz Brushless Conversion Combo
Binding Receiver to Transmitter
Binding is the process of programming the receiver
to recognize the GUID (Globally Unique Identifier)
code of a single specific transmitter and to store
failsafe values. When a receiver is bound to a
transmitter/model memory, the receiver will only
respond to that specific transmitter/model memory.
Binding
1. Press and hold the bind button while
powering on the receiver.
2. The green LED will flash continuously,
indicating that the receiver is in bind mode.
3. Release the bind button.
4. Move the steering wheel and throttle to
the desired failsafe positions.
5. Enter the transmitter into bind mode.
Refer to your transmitter instruction
manual for more information.
6. The green LED on the receiver will be solid when
the receiver and transmitter are bound.
Failsafe
Failsafe positions are stored during binding. In
the unlikely event that the radio link is lost during
use, the receiver will move the servos to their
preprogrammed failsafe positions (normally full
brakes and straight steering). The only time it is
necessary to re-bind your receiver and transmitter
is if you desire different failsafe positions. Always
re-bind your transmitter and receiver after any
changes to throttle channel reversing.
NOTICE: Failsafe protects against signal loss from
the transmitter. Failsafes will not activate in the
event that power to the receiver is lost.
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, Inc. (“Horizon”) warrants to the
original purchaser that the product purchased (the
"Product") will be free from defects in materials and
workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover
(i) cosmetic damage, (ii) damage due to acts of God,
accident, misuse, abuse, negligence, commercial use,
or due to improper use, installation, operation or
maintenance, (iii) modification of or to any part of
the Product, (iv) attempted service by anyone other
than a Horizon Hobby authorized service center,
or (v) Products not purchased from an authorized
Horizon dealer.
OTHER THAN THE EXPRESS WARRANTY ABOVE,
HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY
AND ALL IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE
HAVE DETERMINED THAT THE PRODUCT WILL
SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and
exclusive remedy shall be that Horizon will, at its
option, either (i) service, or (ii) replace, any Product
determined by Horizon to be defective. Horizon
reserves the right to inspect any and all Product(s)
involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon.
Troubleshooting Guide
Problem Possible Cause Solution
The system will not connect Transmitter and receiver too near
each other Move transmitter 8 to 12 feet (2.4 to 3.6 m)
from receiver
Transmitter and receiver too near
large metal objects (vehicles, etc.) Move away from large metal objects
(vehicles, etc.)
Selected model is not bound in
transmitter Make sure correct model memory is selected
and that transmitter is bound to the model
Transmitter accidentally put in bind
mode so receiver is no longer bound Rebind transmitter and receiver
The receiver goes into
failsafe mode a short
distance away from the
transmitter Receiver antenna may be cut or
damaged Replace the receiver antenna
Receiver is not seeing signal from the
transmitter. Make sure receiver antenna is in an antenna
tube and is above vehicle
Receiver quits responding
during operation Low battery voltage Completely recharge battery
Loose or damaged wires or connectors
between battery and receiver Do a check of the wires and connection
between battery and receiver. Repair or
replace wires and/or connectors
Receiver loses its bind Transmitter accidentally put in bind
mode, ending bind to receiver Bind transmitter to receiver
Vehicle moves forward
when brake is applied Transmitter throttle channel is reversed Set transmitter throttle channel to normal
Motor moves without
throttle input Transmitter throttle trim is off-center Set transmitter throttle trim to center
Steering servo operates but
the motor does not run The battery may not be charged Discontinue use and fully charge the battery
Connection from MRX50-BL to
motor is bad Unplug the connection, and plug in the
connection
Motor defective Test independently, repair or replace as
needed
Full Speed not attainable Transmitter adjusted improperly Readjust transmitter settings
Proof of purchase is required for all warranty claims.
SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF
WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
OR ANY OTHER THEORY OF LIABILITY, EVEN IF
HORIZON HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. Further, in no event shall the
liability of Horizon exceed the individual price of the
Product on which liability is asserted. As Horizon
has no control over use, setup, final assembly,
modification or misuse, no liability shall be assumed
nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts
all resulting liability. If you as the purchaser or user
are not prepared to accept the liability associated
with the use of the Product, purchaser is advised to
return the Product immediately in new and unused
condition to the place of purchase.
Law
These terms are governed by Illinois law (without
regard to conflict of law principals). This warranty
gives you specific legal rights, and you may also have
other rights which vary from state to state. Horizon
reserves the right to change or modify this warranty
at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot
provide warranty support or service. Once assembly, setup
or use of the Product has been started, you must contact
Horizon directly. This will enable Horizon to better answer
your questions and service you in the event that you may
need any assistance. For questions or assistance, please
direct your email to [email protected],
or call 877.504.0233 toll free to speak to a Product
Support representative. You may also find information
on our website at www.horizonhobby.com.
Inspection or Services
If this Product needs to be inspected or serviced, please
use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a
Return Merchandise Authorization (RMA) number. Pack
the Product securely using a shipping carton. Please note
that original boxes may be included, but are not designed
to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and
insurance for lost or damaged parcels, as Horizon is not
responsible for merchandise until it arrives and is accepted
at our facility. An Online Service Request is available at
http://www.horizonhobby.com under the Support tab. If
you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with
instructions for submitting your product for service.
When calling Horizon, you will be asked to provide your
complete name, street address, email address and phone
number where you can be reached during business hours.
When sending product into Horizon, please include your
RMA number, a list of the included items, and a brief
summary of the problem. A copy of your original sales
receipt must be included for warranty consideration. Be
sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon.
If you have any issue with a LiPo battery, please
contact the appropriate Horizon Product Support
office.
Warranty Requirements
For Warranty consideration, you must include
your original sales receipt verifying the proof-of-
purchase date. Provided warranty conditions have been
met, your Product will be serviced or replaced free of
charge. Service or replacement decisions are at the
sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty
service will be completed and payment will be
required without notification or estimate of the
expense unless the expense exceeds 50% of the
retail purchase cost. By submitting the item for service
you are agreeing to payment of the service without
notification. Service estimates are available upon request.
You must include this request with your item submitted
for service. Non-warranty service estimates will be
billed a minimum of ½ hour of labor. In addition you
will be billed for return freight. Horizon accepts money
orders and cashiers checks, as well as Visa, MasterCard,
American Express, and Discover cards. By submitting any
item to Horizon for service, you are agreeing to Horizon’s
Terms and Conditions found on our website http://www.
horizonhobby.com/Service/Request/.
Compliance Information
for the European union
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2011103004
Product(s):
Micro 2.4GHz Brushless
Conversion Combo, 8750KV
Item Number(s): LOSB9593
Equipment class: 1
The object of declaration described above is in
conformity with the requirements of the specifica-
tions listed below, following the provisions of the
European R&TTE directive 1999/5/EC and EMC
Directive 2004/108/EC:
EN 301 489-1 V1.7.1: 2006
EN 301 489-17 V1.3.2: 2008
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
October 30, 2011
Instructions for Disposal
of WEEE by Users in the
European Union
This product must not be disposed of with other
waste. Instead, it is the user’s responsibility to
dispose of their waste equipment by handing
it over to a designated collection point for the
recycling of waste electrical and electronic
equipment. The separate collection and recycling
of your waste equipment at the time of disposal
will help to conserve natural resources and ensure
that it is recycled in a manner that protects human
health and the environment. For more information
about where you can drop off your waste
equipment for recycling, please contact your local
city office, your household waste disposal service
or where you purchased the product.
Steven A. Hall
Vice President
International Operations
and Risk Management
Horizon Hobby, Inc.
Contact Information
Country of Purchase Horizon Hobby Address Phone Number/Email Address
United States
of America
Horizon Service Center
(Electronics and engines) 4105 Fieldstone Rd
Champaign, Illinois 61822 USA 877-504-0233
Online Repair Request:
visit www.horizonhobby.com/service
Horizon Product Support
(All other products)
4105 Fieldstone Rd
Champaign, Illinois 61822 USA 877-504-0233
[email protected]
United Kingdom Horizon Hobby Limited Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS, United Kingdom +44 (0) 1279 641 097
[email protected]
Germany Horizon Technischer Service Christian-Junge-Straße 1
25337 Elmshorn, Germany +49 (0) 4121 2655 100
[email protected]
France Horizon Hobby SAS 14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron +33 (0) 1 60 47 44 70
[email protected]
LOSB9593 Micro 2.4GHz Brushless Conversion Combo
DE
HINWEIS
Alle Anweisungen, Garantien und dazugehörigen
Dokumente können ohne Ankündigung von Horizon
Hobby Inc. geändert werden. Eine aktuelle Version
ersehen Sie bitte im Support Feld unter:
http://www.horizonhobby.com.
Erklärung der Begriffe
Die folgenden Begriffe werden in der gesamten
Produktliteratur verwendet, um auf unterschiedlich
hohe Gefahrenrisiken beim Betrieb dieses Produkts
hinzuweisen:
HINWEIS: Wenn diese Verfahren nicht korrekt
befolgt werden, können sich möglicherweise
Sachschäden UND geringe oder keine Gefahr
von Verletzungen ergeben.
ACHTUNG: Wenn diese Verfahren nicht korrekt
befolgt werden, ergeben sich wahrscheinlich
Sachschäden UND die Gefahr von schweren
Verletzungen.
WARNUNG: Wenn diese Verfahren nicht korrekt
befolgt werden, ergeben sich wahrscheinlich
Sachschäden, Kollateralschäden und schwere
Verletzungen ODER mit hoher Wahrscheinlichkeit
oberflächliche Verletzungen.
WARNUNG: Lesen Sie sorgfältig die gesamte
Bedienungsanleitung durch und machen sich vor
dem Betrieb mit dem Produkt vertraut. Falscher
und oder nicht sachgemäßer Umgang kann zu
Beschädigungen am Produkt, eigenen und fremden
Eigentum und ernsthaften Verletzungen führen.
Bitte beachten Sie, dass dieses Produkt ein hoch
entwickeltes Hobby Produkt und kein Spielzeug
ist. Es erfordert bei dem Betrieb Aufmerksamkeit
und grundlegende mechanische Fähigkeiten.
Falscher, nicht sachgemäßer Umgang kann zu
Beschädigungen an eigenem oder fremden
Eigentum oder zu Verletzungen an sich selbst
oder Dritter führen. Versuchen Sie nicht dieses
Produkt auseinander zu bauen, oder es mit
Komponenten zu betreiben die nicht ausdrücklich
mit Genehmigungvon Horizon Hobby dafür
geeignetsind. Dieses Produkt ist nicht für den
Gebrauch von Kindern ohne direkte Aufsicht durch
ihre Eltern bestimmt. Die Bedienungsanleitung enthält
Anweisungen und wichtige Informationen für die
Sicherheit und Betrieb. Es ist daher notwendig, allen
darin enthaltenen Anweisungen und Warnungen Folge
zu leisten und diese Anleitung vor dem Zusammenbau
und Inbetriebnahme sorgfältig durch zu lesen.
Altersempfehlung:
Nicht geeignet für Kinder unter
14 Jahren. Dies ist kein Spielzeug.
Übersicht
Die 2-in-1 MRX50BLRegler und Spektrum 2,4 GHz
Empfänger Einheit wurde für den Umbau der Losi®
Micro RTRs (Maßstab 1/24- und 1/36-) entwickelt. Der
MRX-50BL bietet für Bürsten oder Bürstenlose Motoren
fantastische Leistungen, eine verbesserte Reichweite und
störungsfreien Betrieb.
Bei dem Brushless Betrieb werden Sie werden Sie einen
erheblichen Zuwachs bei der Leistung und Drehmoment
feststellen.
Inklusive
1 MRX50-BL Regler
4 M1.6 x 6 Schrauben
3 M1.6 x 4 Schrauben
2 Motor Schrauben
1 Kabeladapter (3-fach Kabel zu 2-fach-Kabel)
1 Micro 1/24 Chassis Abdeckung für MRX50-BL
Sicherheitshinweise
• Motor und Regler sind bei und nach Betrieb heiß.
Bitte nicht berühren.
• Der Betrieb eines Bürstenmotors mit einem 3S (11,1
Volt) LiPo Akku beschädigt Motor und / oder den
Regler und ist nicht durch die Garantie abgedeckt.
• Nur für den Brushless Motor: Versuchen Sie bitte
nicht das Ritzel abzunehmen da dadurch der Motor
beschädigt wird und die Garantie erlischt.
Eigenschaften
• Kompatibel mit allen Spektrum Surface Sendern
• Vorbereitet für den Brushless Betrieb. Schließen Sie
einfach einen Brushless (Bürstenlosen) Motor an
und genießen die extra Leistung und verbesserte
Lebensdauer des Motors
• Ersetzt passend den original Regler/Empfänger.
Keine weiteren Modifikationen oder zusätzliche
Komponenten notwendig
• Kompatibel mit Losi 5 oder 3 adrigen Servos
• Kompatibel mit 2S–3S LiPo oder NiMH Akkus mit
Autoabschaltung. 3S (11,1Volt nur für den Betrieb
mit Brushless Motoren.)
• Vorwärts, Bremse und Rückwärts Einstellungen
• Inklusive Mikro 3 auf 2 Kabel Stecker für einfachen
Bürsten oder Bürstenlosen Betrieb
• Kraftvoller 8750KV Motor extreme Leistung,
Drehmoment und Höchstgeschwindigkeit
• Langlebiges 12 Zahn Metall Ritzel für verbesserte
Betriebssicherheit
Spezifikationen
MRX50-BL
Motor Typ Brushless Sensorlos
Brushed (Auto Detektion)
Niederspannungsabschaltung 2S und 3S LiPo Akku
Automatische
Akkutyp Erkennung Yes
Eingangsspannung
4-Zellen (4.8-volt) NiMH/NiCd
Bürstenmotoren oder 2S (7.4-volt) LiPo Akku
NICHT 3S kompatibel
Eingangsspannung 4-Zellen (4.8-volt) NiMH/NiCd
Brushlessmotoren oder 2S (7.4-volt) bis 3S
(11.1-volt) LiPo Akku
Dauerstrom
(Spitzenstrom kurzz.) 5A (20A)
Innenwiederstand
.063 Ohm
Motor Limit 10250KV
Motor Micro 3-Anschlußkabel
Akkuanschluß Micro 2-Kabel
Abmessungen 42mm x 31mm x 8.5mm
Gewicht (mit Kabel) 8.4 g
BEC Leistung
5.0V/1.0A
Signal Typ DSM
Signal Band 2.4GHz
Akku Anschluß 2 Kabel
OFF (AUS)
ON (EIN)
Schalter
Motoranschlußstecker 3 Kabel
Bindeknopf
3-adriger
Servoanschluß
5-adriger Servoanschluß
LOSB9470 8750KV
Motor Typ Sensorlos
Eingangsspannung
24-Zellen (4.8-volt) NiMH/
NiCd oder 2S (7.4-Volt)
bis 3S (11.1-Volt) LiPo
Abmessungen Gehäuse Durchmesserer:
12.0mm
Gehäuse Länge: 22.1mm
Wellendurchmesser: 1.5mm
Wellenlänge: 7.6mm
Gewicht
(mit Kabel u. Ritzel) 9.0 g
Motor
Connector Type Micro 3-Wire
EN