Losi LOSA3358 User Manual
Losa
A3354
O-Ring, (10 x 1)mm
One-Way Tube
2 x One-Way Shaft
A3354
5 x 2-56 x 1/4" Button
Retaining Washer
2 x One-way
2 x 1/4" x 3/8" Bearing
A6921
2 x O-Ring, (9 x 1)mm
A3354
2 x One-Way Outdrive
A3353
Head Screws
A6255
42T One-Way Pulley
A3326
Pulley Shim
A3354
A3354
One-Way bearings
come pre-installed
into the One-Way Tube
from the factory.
A3354
O-Ring, (10 x 1)mm
One-Way Tube
2 x One-Way Shaft
A3354
5 x 2-56 x 1/4" Button
Retaining Washer
2 x One-way
2 x 1/4" x 3/8" Bearing
A6921
2 x O-Ring, (9 x 1)mm
A3354
2 x One-Way Outdrive
A3353
Head Screws
A6255
42T One-Way Pulley
A3326
Pulley Shim
A3354
A3354
One-Way bearings
come pre-installed
into the One-Way Tube
from the factory.
Install a One-Way Shaft, Retaining Washer, and Bearing and Ensure proper seating of the 9
x 1mm O-rings into the grooves inside each end of the One-Way Tube.
Install the One-Way Pulley followed by the Pulley Shim onto the One-Way Tube. Align the
small holes in the Pulley with the holes in the Tube when installing the 3 2-56 x 1/4” Button
Head Screws.
Install and secure a One-Way Outdrive onto the Pulley Side of the One-Way by aligning the
square portions of the Outdrive and Shaft.
Install the assembly into the front end of your JRX-S Type R as would be done with a stan-
dard diff (remove eccentric by removing bulkhead cap screws and the 10 x 1mm O-Ring).
Install the 10 x 1mm O-Ring into the groove on the end of the One-Way Tube protruding
thorugh the left front bulkhead.
Install the second Outdrive onto the other One-Way Shaft as done previously and re-install
into the car. Re-install bulkhead caps and set belt tension.
•
•
•
•
•
•
Install a One-Way Shaft, Retaining Washer, and Bearing and Ensure proper seating of the 9
x 1mm O-rings into the grooves inside each end of the One-Way Tube.
Install the One-Way Pulley followed by the Pulley Shim onto the One-Way Tube. Align the
small holes in the Pulley with the holes in the Tube when installing the 3 2-56 x 1/4” Button
Head Screws.
Install and secure a One-Way Outdrive onto the Pulley Side of the One-Way by aligning the
square portions of the Outdrive and Shaft.
Install the assembly into the front end of your JRX-S Type R as would be done with a stan-
dard diff (remove eccentric by removing bulkhead cap screws and the 10 x 1mm O-Ring).
Install the 10 x 1mm O-Ring into the groove on the end of the One-Way Tube protruding
thorugh the left front bulkhead.
Install the second Outdrive onto the other One-Way Shaft as done previously and re-install
into the car. Re-install bulkhead caps and set belt tension.
•
•
•
•
•
•
LOSA
LOSA
3358
3358
LOSA
LOSA
3358
3358
800-0331
800-0331
800-0331
800-0331
Front One-Way Assembly
STEP A-01
Front One-Way Assembly
STEP A-01