Dell PowerEdge 2850 User Manual
Page 20
I/O parity interrupt at address
Faulty or improperly installed
expansion card.
See "
Troubleshooting Expansion Cards
" in
"Troubleshooting Your System."
Invalid configuration information - please run
SETUP program
Incorrect configuration settings in
System Setup program; NVRAM_CLR
jumper is installed; faulty system
battery.
Check the System Setup configuration settings. See "Using
the System Setup Program" in the User's Guide. Remove
the NVRAM_CLR jumper. See
Figure A
-2
for jumper location.
If the problem persists, see "
Troubleshooting the System
Battery
" in "Troubleshooting Your System."
Invalid NVRAM configuration, resource re-
allocated
System configuration data has been
ignored.
Check the System Setup configuration settings. See "Using
the System Setup Program" in the User's Guide.
Invalid SCSI configuration
SCSI cable detected on connector SCSIB of the
SCSI backplane, daughter card not present
A SCSI cable is connected to the
channel B connector on the SCSI
backplane board; SCSI backplane
daughter card is not installed.
If a cable is connected to the SCSIB backplane board
connector, the SCSI backplane daughter card must be
installed. Install the backplane daughter card. See
"
Installing a SCSI Backplane Daughter Card
" in "Installing
Drives."
Keyboard controller failure
Faulty keyboard controller; faulty
system board.
See "
Getting Help
."
Keyboard clock line failure
Loose or improperly connected
keyboard cable; faulty keyboard; faulty
keyboard controller.
See "
Troubleshooting the Keyboard
" in "Troubleshooting
Your System."
Keyboard data line failure
Keyboard failure
Keyboard stuck key failure
Memory address line failure at address, read
value expecting value
Faulty or improperly installed memory
modules.
See "
Troubleshooting System Memory
" in "Troubleshooting
Your System."
Memory double word logic failure at address, read
value expecting value
Memory high address line failure at start address
to end address
Memory high data line failure at start address to
end address
Memory odd/even logic failure at start address to
end address
Memory write/read failure at address, read value
expecting value
Memory parity failure at start address to end
address
Faulty or improperly installed memory
modules.
See "
Troubleshooting System Memory
" in "Troubleshooting
Your System."
Memory parity error at address
No boot device available
Faulty or missing optical/diskette drive
subsystem, hard drive, or hard-drive
subsystem.
Use a bootable diskette, CD, or hard drive. If the problem
persists, see "
Troubleshooting a Diskette Drive
,"
"
Troubleshooting an Optical Drive
," and "
Troubleshooting
SCSI Hard Drives
" in "Troubleshooting Your System."
No boot sector on hard-disk
No operating system on hard drive.
Check the hard-drive configuration settings in the System
Setup program. See "Using the System Setup Program" in
the User's Guide.
No PXE-capable device available
PXE devices are detected.
Check the configuration settings in the System Setup
program for the NICs. See "Using the System Setup
Program" in the User's Guide. If the problem persists, see
"
Troubleshooting a NIC
" in "Troubleshooting Your System."
No timer tick interrupt
Faulty system board.
See "
Getting Help
."
Not a boot diskette
No operating system on diskette.
Use a bootable diskette.
PCI BIOS failed to install
Loose cables to expansion card(s);
faulty or improperly installed
expansion card.
Ensure that all appropriate cables are securely connected
to the expansion cards. If the problem persists, see
"
Troubleshooting Expansion Cards
" in "Troubleshooting
Your System."
PCIe Degraded Link Width Error: Embedded
Bus#nn/Dev#nn/Funcn
Expected Link Width is n
Actual Link Width is n
Faulty or improperly installed PCIe card
or expansion-card cage.
Reseat the PCIe cards and the expansion-card cage. See
"
Expansion-Card Cage
" and "
Expansion Cards
." If the
problem persists, see "
Getting Help
."
PCIe Degraded Link Width Error: Slot n
Expected Link Width is n
Actual Link Width is n
Faulty or improperly installed PCIe card
in the specified slot number.
Reseat the PCIe card in the specified slot number. See
"
Expansion Cards
." If the problem persists, see "
Getting
Help
."
PCIe Training Error: Embedded Bus#nn/Dev#nn/Funcn
Faulty or improperly installed PCIe card
or expansion-card cage.
Reseat the PCIe cards and the expansion-card cage. See
"
Expansion-Card Cage
" and "
Expansion Cards
." If the
problem persists, see "
Getting Help
."
PCIe Training Error: Slot n
Faulty or improperly installed PCIe card
in the specified slot number.
Reseat the PCIe card in the specified slot number. See
"
Expansion Cards
." If the problem persists, see "
Getting
Help
."
Plug & Play Configuration Error Embedded xxx
Error encountered in initializing PCI
device; faulty system board.
Install the NVRAM_CLR jumper and reboot the system. See
Figure A
-2
for jumper location. If the problem persists, see
"
Troubleshooting Expansion Cards
" in "Troubleshooting
Your System."
Plug & Play Configuration Error PCI_n
Error encountered in initializing PCI
adapter.
Primary backplane is not present
Faulty or improperly installed SCSI
backplane board.
See "
Getting Help
."