Tweco CutMaster 101 with SL100SV - Manual (Page 55)

Manual 0-4642 4-15 OPERATION
4
4.10 Cutting Speed Charts: Stainless Steel, SL100 Torch with Exposed Tip
NOTES
*Gas pressure shown is for torches with leads up to 25' / 7.6 m long. For 50' / 15.2 m leads, increase pressure by 5 psi / 0.34 bar.
This information represents realistic expectations using recommended practices and well - maintained systems.
Actual speeds may vary up to 50% from those shown.
Electrode Start Cartridge Tip Shield Cup Body Shield Cap, Deflector
9-8215 9-8213 9-8237 9-8243
Art # A-04203
Table: Dry
Gas: Compressed Air
Material thickness Tip Current
Plasma
Press.*
Pierce
Time
Arc
voltage
Stand-off
Height
Recommended
Travel Speed
In GA mm Cat. # Amps PSI In mm SEC Volts in mm IPM mm/min
0.038 20 0.95 8-8208 40 65 0.188 4.8 0.00 103 0.19 4.80 357 9067.8
0.050 18 1.27 8-8208 40 65 0.188 4.8 0.00 104 0.19 4.80 287 7289.8
0.063 16 1.60 8-8208 40 65 0.188 4.8 0.10 104 0.19 4.80 244 6197.6
0.078 14 1.98 8-8208 40 65 0.188 4.8 0.30 105 0.19 4.80 125 3175
0.135 3.43 8-8208 40 65 0.188 4.8 0.40 105 0.19 4.80 106 2692.4
0.141 10 3.58 8-8208 40 65 0.188 4.8 0.50 106 0.19 4.80 104 2641.6
0.188 4.78 8-8208 40 65 0.188 4.8 0.60 106 0.19 4.80 75 1905
0.250 6.35 8-8208 40 65 0.188 4.8 1.00 109 0.19 4.80 46.6 1183.64
0.375 9.53 8-8208 40 65 NR NR NR 109 0.19 4.80 31.5 800.1
0.500 12.70 8-8208 40 65 NR NR NR 112 0.19 4.80 17.4 441.96
0.625 15.88 8-8208 40 65 NR NR NR 114 0.19 4.80 10 254
0.063 16 1.57 9-8210 60 70 0.188 4.8 0.00 107 0.19 4.80 177 4495.8
0.078 14 1.98 9-8210 60 70 0.188 4.8 0.10 108 0.19 4.80 169 4292.6
0.125 11 3.18 9-8210 60 70 0.188 4.8 0.10 109 0.19 4.80 140 3556
0.135 3.43 9-8210 60 70 0.188 4.8 0.10 110 0.19 4.80 117 2971.8
0.141 10 3.58 9-8210 60 70 0.188 4.8 0.15 111 0.19 4.80 103 2616.2
0.188 4.78 9-8210 60 70 0.188 4.8 0.20 112 0.19 4.80 90 2286
0.250 6.35 9-8210 60 70 0.188 4.8 0.30 113 0.19 4.80 68.8 1747.52
0.375 9.53 9-8210 60 70 0.188 4.8 0.50 115 0.19 4.80 35 889
0.500 12.70 9-8210 60 70 0.188 4.8 0.75 121 0.19 4.80 21.3 541.02
0.625 15.88 9-8210 60 70 NR NR NR 127 0.19 4.80 15.9 403.86
0.750 19.05 9-8210 60 70 NR NR NR 131 0.19 4.80 12.5 317.5
1.000 25.40 9-8210 60 70 NR NR NR 135 0.19 4.80 6 152.4
0.048 18 1.22 9-8211 80 65 0.188 4.8 0.05 102 0.19 4.80 411 10439.4
0.125 11 3.18 9-8211 80 65 0.188 4.8 0.05 104 0.19 4.80 291 7391.4
0.135 3.43 9-8211 80 65 0.188 4.8 0.10 105 0.19 4.80 270 6858
0.188 4.78 9-8211 80 65 0.188 4.8 0.20 106 0.19 4.80 171 4343.4
0.250 6.35 9-8211 80 65 0.188 4.8 0.30 107 0.19 4.80 88 2235.2
0.375 9.53 9-8211 80 65 0.188 4.8 0.40 111 0.19 4.80 47 1193.8
0.500 12.70 9-8211 80 65 0.188 4.8 0.60 113 0.19 4.80 28.8 731.52
0.625 15.88 9-8211 80 65 0.188 4.8 0.75 117 0.19 4.80 19.5 495.3
0.750 19.05 9-8211 80 65 NR NR NR 120 0.19 4.80 15.6 396.24
0.875 22.23 9-8211 80 65 NR NR NR 123 0.19 4.80 12 304.8
1.000 25.40 9-8211 80 65 NR NR NR 126 0.19 4.80 10 254
1.250 31.75 9-8211 80 65 NR NR NR 130 0.19 4.80 6 152.4
Material: Stainless Steel
Pierce Height
Torch: SL100 with Exposed Tip and Deflector
Power Supply: CutMaster 101 Automated