Powers e480 Series Under-the-Counter Combination Tempering Valves for Low Flow Control - Manual (Page 2)

Temperature Adjustment
n
1. Loosen locknut.
2. Turn on fixture and run water for at least two minutes to allow
supply temperature to stabilize.
3. Turn temperature stem counter-clockwise for hotter or
clockwise for colder outlet temperature.
4. Tighten locknut to prevent accidental or unauthorized
temperature adjustment.
5. Re-check outlet temperature.
Repair Kit
n
Motor Repair Kit: .................................................................... 480 270
1. Mark pipe as shown.
This is pipe insertion depth.
2. Clean pipe end.
1. Remove collet clip. 2. Depress collet.
3. Pull tubing from tailpiece .
3. If using PEX tubing, insert pipe stiff-
ener (provided) into end of pipe.
4. Push tubing into tailpiece up to mark.
5. Insert collet clip.
PEX tubing only
Pipe Stiffener
Tail Piece
Mark
Collet clip
Collet depressed
Quick-Connect Installation
n
TO CONNECT
TO DISCONNECT
1 in. (25.4mm)
PEX
PEX tubing only
Pipe Stiffener
Mark
Collet clip
Collet depressed
Collet
Collet clip
Collet 3 / 8 in.Pipe (9.5mm)
To Install
n
1. Installation should be in accordance with acceptable
plumbing practices. Flush all piping thoroughly before
installation. Installation and
field adjustment are the respon-
sibility of the installer.
2. Locate suitable place for the
tempering valve. Valve should
be accessible for service and
adjustment and as close to the
point-of-use as possible.
3. Connect hot and cold supplies
to valve and outlet of tempering valve to fixture (s) using 1 /
2
"
or 3 /
8
" compression connections. For Quick-Connect refer
to Quick-Connect installation section.
4. Turn on hot and cold water supplies. If any leaks are
observed, tighten connections as necessary to stop leaks
before proceeding.
5. Turn on fixture and allow water to flow for 2 minutes.
Measure water temperature at the outlet. If water is not at
desired temperature, adjust as necessary (see temperature
adjustment section). Maximum outlet temperature of 105°F
(41°C) is recommended.
Typical Installation
Warranty
n
The Seller warrants that the equipment manufactured by it and covered by this order or contract is free from defects in material and workmanship and, without
charge, equipment found to be defective in material or workmanship will be repaired, or at Seller’s option replaced F.O.B. original point of shipment, if written
notice of failure is received by Seller within one (1) year after date of shipment (unless specifically noted elsewhere), provided said equipment has been properly
installed, operated in accordance with the Seller’s instructions, and provided such defects are not due to abuse or decomposition by chemical or galvanic action.
ThiS expreSS warranTy iS in lieu OF and excludeS all OTher warranTieS, guaranTeeS, Or repreSenTaTiOnS, expreSS OF implied. There are
nO implied warranTieS OF merchanTaBiliTy Or OF FiTneSS FOr a parTicular purpOSe. The Seller assumes no responsibility for repairs made on the
Seller’s equipment unless done by the Seller’s authorized personnel, or by written authority from the Seller. The Seller makes no guarantee with respect to material
not manufactured by it.
USA: Phone: 1.800.669.5430 • Fax 1.847. 229.0526 • www.powerscontrols.com
Canada: Phone: 1.888.208.8927 • Fax 1.888.479.2887 • www.powerscontrols.ca
IS-P-e480 1336 EDP# 6512252 © 2013 Powers
A Watts Water Technologies Company
WARNING: This product contains chemicals known to the
State of California to cause cancer and birth defects or
other reproductive harm.
For more information: www.watts.com/prop65