Powers 440 Series Fotoguard - Manual (Page 2)

© May 2001 Powers, a Watts Industries Co.
3400 Oakton Street, Skokie, IL 60076 Phone: 800.669.5430 • 847.673.6700 • Fax: 847.673.9044
www.powerscontrols.com
5435 North Service Road, Burlington, Ontario, L7L 5H7 Canada • Phone: 888.208.8927 • Fax: 888.882.1979
A Watts Industries Co.
129-008 Page 2
SERIES 440
FOTOGUARD
TROUBLESHOOTING RECOMMENDED REPAIR KIT
Gasket and Disc 1. Water leak at stem and/or bonnet 227-338
Replacement (Item 1 for models 4, 5, 6, and 7) Includes items: 1, 2, 3A, 3B, 4A, & 8
2. Flow of water continues after mixer is turned off
Motor Replacement 3. Variable or untempered discharge temperature (65-115°F) 227-339
Includes items: 2, 3, 3A, 3B, 7, & 8
Valve and Hot Water 4. Flow of water continues after mixer is turned off due to 227-340
Seat Replacement worn to hot water seat (6) (Models 5, 6, & 7)
5. Variable discharge temperature continues after Includes items: 2, 4A, 5, 6, 7, & 8
replacement of motor (3)
Combination Seat 6. Flow of water continues after mixer is turned off and shutoff 227-351
Replacement Std. Cap. disc (3B) and/or hot water seat (6) has been replaced Includes items: 2, 4, 4A, & 8
High Capacity Kit 7. To increase capacity of mixer to 9.0 gpm @ 45 psi diff. 227-431 (Models 5, 6, & 7)
(0.57 l/s @ 310 kPa) Includes items: 2, 4, 4A, 5, 6, & 8
Low Capacity Kit 8. To decrease capacity of mixer to 1.5 gpm @ 45 psi diff. 227-445 (Models 5, 6, & 7)
(0.061 l/s @ 310 kPa) Includes items: 2, 4, 4A, 5, 6, & 8
For parts not covered above, refer to Technical Instruction Form MV440-2.
SERIES 440
FOTOGUARD
High Capacity
TROUBLESHOOTING RECOMMENDED REPAIR KIT
Gasket and Disc 1. Water leak at stem and/or bonnet 225-357
Replacement (Item 1 for models 4, 5, 6, and 7) Includes items: 1, 2, 3, 4A, & 5A
2. Flow of water continues after mixer is turned off
Valve and Cylinder 3. Variable or untempered discharge temperature 225-393*
Replacement (Lime deposits can be removed with the use of various Includes items: 3, 5, 5A, & 6
commercially available products designed for this purpose.)
Motor Replacement 4. If items 5 and 6 are free of lime and free-moving and 225-395
discharge temperature is variable or untempered Includes items: 3, 4, and 4A
For easy removal of piston cylinder (item 6), order special wrench, part no. 225-350.
For parts not covered above, refer to Technical Instruction Form MV440-2.
* The valve assembly (5) and cylinder (6) must both be replaced at the same time when using this kit.
Do not use the new valve with an old cylinder, or vice versa.
TROUBLESHOOTING AND REPAIR
To determine model number of Hydroguard, refer to nameplate on body assembly.
5 Y4
Model Number Date of Manufacture
Form 129-008 0218 EDP# 6512201 PRINTED IN U.S.A.