Bang & Olufsen BeoVision Avant (1995-2005) - User Guide - Manual (Page 11)

11
What’s on the first TV tuning menu…
Freq (frequency)... Searching stops at the first
station producing an acceptable signal. If you
know a station’s exact frequency number, key it in
directly using the number buttons.
(System)… If System appears on the menu, make
sure that the correct broadcast system is displayed
before you start tuning:
B/G...
for PAL/SECAM B/G
I... for PAL I
L... for SECAM L
M... for NTSC
D/K... for PAL/SECAM D/K
Note: All options may not be available as this
depends on the television type.
Pr (program number)... Key in the program
number (1-99) you wish to preset the station on.
Name (naming)... The name you give a station
will appear in the TV program list.
Press ▲ or ▼ to reveal the character you want.
Press 0 to switch from upper to lower case, or vice
versa. Then press
tt to move on to the next
character position.
Then press GO or move on to More... When
you have entered the information you want, press
GO to store your TV program or….
More… If it is necessary to fill in extra
information, move to More and press GO. A
second TV tuning menu appears for fine tuning,
availability of decoder and type of sound or
format.
What’s on the second TV tuning menu…
Fine (fine tuning)... The TV automatically tunes to
the best possible picture. However, neighbouring
channels may blur the picture slightly, in which
case fine tuning may be required. You fine tune
by 8 steps above or below the standard frequency.
Decoder... If you tune in a coded TV station and
want the decoder to be cut in automatically, set
the item Decoder to one of the On options below:
ON/AV...
(decoder on) where both audio and
video signals are coded
ON/V... (decoder on) where only video
signals are coded
OFF... (decoder off) for no decoder
Select ON/AV for most coded programs to get
both sound and pictures. If only the video signal is
coded, select ON/V. If you select ON/AV where
only the video signal is coded, the sound may be
lost when the signal is decoded.
Note: If an extra decoder is connected to the
BeoVision Avant AV socket and Decoder-2 is
entered into the AV Source menu ( see page 50,
Extra video equipment), you can choose between
1/AV or 1/V, for decoder-1, and 2/AV or 2/V for
decoder-2 or OFF for no decoder.
Sound (mono/stereo/language)... Several types of
sound may available for a TV station, for example
both stereo and mono sound, or several different
languages. Press
▲ or ▼ to switch between the
sound modes currently transmitted, when the
sound you wish to store is heard/displayed, press
GO.
Note: Even though you store a type of sound/
language in this way, you can still switch between
the various types of sound while you are watching
this TV station.
Press LIST to display SOUND* or MONO* on the
Beo4 remote control, then press GO repeatedly to
switch sound. See page 35, Switching sound for
more information about the various types of
sound available.
*Note: In order to display SOUND or MONO on
Beo4, you must add the function to the Beo4 LIST
function, see Extra functions in Beo4, page 67.
Format... Two format settings are available, you
can store a format for each TV program. The
default setting is 15:9, but if ”noise” appears in
the right and left side of the picture, choose the
14:9 format instead, enabling the curtains on the
TV screen to hide the ”noise”. You can still
change the picture format for each program even
though you have stored a setting, see page 56-57.
Removing a tuned TV station…
Press MENU to call up the main menu, press 3
to select TV list and press GO to call up the TV
program list, use the
▲ and ▼ buttons to
move the cursor to the station you want to
remove. Then press MENU. When Clr? appears,
press GO to clear the program. See Program
list, page 25, for further information.