AEM 30-3532 GM LS 24x Engines Layover - Manual (Page 18)

Rev A, 2013/02/05
C1-38 Analog_In_10 12 bit A/D, 100K pullup to 5V
0-5V analog signal. Use +5V Out pins as power supply and
Sensor Ground pins as the low reference. Do not connect
signals referenced to +12V as this can permanently
damage the ECU. See the Setup Wizard Barometric
Pressure page for setup and calibration. Monitor the
BaroPress [kPa] channel.
C1-39 Analog_In_11 12 bit A/D, 100K pullup to 5V
0-5V analog signal. Use +5V Out pins as power supply and
Sensor Ground pins as the low reference. Do not connect
signals referenced to +12V as this can permanently
damage the ECU.
See the 1D lookup table 'ShiftSwitch' for setup. Also
assignable to multiple functions. See Setup Wizard for
details.
C1-40 Analog_In_12 12 bit A/D, 100K pullup to 5V
0-5V analog signal. Use +5V Out pins as power supply and
Sensor Ground pins as the low reference. Do not connect
signals referenced to +12V as this can permanently
damage the ECU.
See the 1D lookup table 'ModeSwitch' for input state.
A multi-position rotary switch such as AEM P/N 30-2056 is
recommended.
Also assignable to multiple functions. See Setup Wizard
for details.
C1-41 +5V_Out_1 Regulated, fused +5V supply for sensor power Analog sensor power
C1-42 +5V_Out_1 Regulated, fused +5V supply for sensor power Analog sensor power
C1-43 HighsideSwitch_1 0.7A max, High Side Solid State Relay
See Setup Wizard page 'HighSide Assigment Tables' for
configuration options. See 2D lookup table 'HS1_Table'
for activation settings.
C1-44 HighsideSwitch_0 0.7A max, High Side Solid State Relay
See Setup Wizard page 'HighSide Assigment Tables' for
configuration options. See 2D lookup table 'HS0_Table'
for activation settings.
See Setup Wizard page 'VTEC' for default activation
criteria.
C1-45
Crankshaft Position
Sensor VR+
Differential Variable Reluctance Zero Cross
Detection
See Setup Wizard page Cam/Crank for options.
C1-46
Crankshaft Position
Sensor VR-
See Setup Wizard page Cam/Crank for options.
C1-47
Camshaft Position Sensor
1 VR-
Differential Variable Reluctance Zero Cross
Detection
See Setup Wizard page Cam/Crank for options.
C1-48
Camshaft Position Sensor
1 VR+
See Setup Wizard page Cam/Crank for options.
C1-49 VR+_In_2
Differential Variable Reluctance Zero Cross
Detection
See Non Driven Wheel Speed Calibration in the Setup
Wizard Vehicle Speed page.
C1-50 VR-_In_2
C1-51 VR-_In_3
Differential Variable Reluctance Zero Cross
Detection
See Driven Wheel Speed Calibration in the Setup Wizard
Vehicle Speed page.
C1-52 VR+_In_3
C1-53 DBW1 Motor - 5.0A max Throttle Control Hbridge Drive +12V to close
C1-54 DBW1 Motor + 5.0A max Throttle Control Hbridge Drive +12V to open
C1-55 Power Ground Power Ground Connect directly to battery ground
C1-56 Injector 6 Saturated or peak and hold, 3A max continuous Injector 6
C1-57 Injector 5 Saturated or peak and hold, 3A max continuous Injector 5
C1-58 Injector 4 Saturated or peak and hold, 3A max continuous Injector 4