Viewing the array configuration, Configuring simple-swap sata raid, Enabling the serial ata (sata) controller – Lenovo ThinkServer TD100x User Manual
Page 72: Configuring, Simple-swap, Sata, Raid, Viewing, Array, Configuration
Viewing
the
array
configuration
To
view
information
about
the
RAID
array,
complete
the
following
steps:
1.
Start
the
RAID
Configuration
Utility
program.
2.
From
the
RAID
Configuration
Utility
window,
select
Manage
Arrays.
3.
Select
an
array
and
press
Enter.
4.
To
exit
from
the
program,
press
Esc.
Configuring
simple-swap
SATA
RAID
Use
the
Adaptec
RAID
Configuration
Utility
program
to
configure
and
manage
simple-swap
SATA
redundant
array
of
independent
disks
(RAID)
on
simple-swap
SATA
models
with
no
ServeRAID
adapter
installed.
This
utility
is
part
of
the
BIOS
code.
The
Adaptec
RAID
Configuration
Utility
program
adds
RAID
functionality
to
the
integrated
SATA
controller.
The
integrated
Serial
ATA
(SATA)
controller
comes
disabled
by
default.
You
must
enable
it
and
install
the
device
drivers
before
you
can
use
it.
The
device
drivers,
documentation,
and
other
information
are
available
on
the
IBM
ServeRAID-8kl
(Adaptec
HostRAID)
Support
CD.
Enabling
the
Serial
ATA
(SATA)
controller
To
enable
the
SATA
RAID
controller,
complete
the
following
steps:
1.
Turn
on
the
server.
2.
When
the
prompt
Press
F1
for
Configuration/Setup
appears,
press
F1.
If
you
have
set
an
administrator
password,
you
are
prompted
to
type
the
password.
3.
Select
Devices
and
I/O
Ports
-->
Advanced
Chipset
Control.
4.
Select
SATA
Controller
Mode
Option.
Change
the
value
to
Enhanced.
5.
Scroll
down
and
select
SATA
RAID
Enable.
6.
Select
Enabled.
7.
Press
Esc;
then,
select
Yes
to
save
the
changes.
Using
the
Adaptec
RAID
Configuration
Utility
program
Note:
Adaptec
RAID
(also
known
as
HostRAID)
is
not
supported
on
the
SCO
6.0
and
UnixWare
7.14
operating
systems.
Use
the
Adaptec
RAID
Configuration
Utility
program
to
perform
the
following
tasks:
v
Configure
a
redundant
array
of
independent
disks
(RAID)
array
v
View
or
change
the
RAID
configuration
and
associated
devices
For
additional
information
about
using
the
Adaptec
RAID
Configuration
Utility
program,
see
the
documentation
on
the
IBM
ServeRAID-8kl
(Adaptec
HostRAID)
Support
CD
that
comes
with
the
server.
Adaptec
RAID
Configuration
Utility
menu
choices:
The
following
choices
are
on
the
Adaptec
RAID
Configuration
Utility
menu:
v
Array
Configuration
Utility
Select
this
choice
to
create,
manage,
or
delete
arrays,
add
or
delete
a
hot-spare
drive,
or
initialize
drives.
v
SerialSelect
Utility
Select
this
choice
to
configure
the
controller
interface
definitions
or
to
configure
the
physical
transfer
and
SATA
address
of
the
selected
drive.
56
ThinkServer
TD100
and
TD100x
Types
4203,
4204,
4205,
4206,
6398,
6399,
6419,
and
6429:
Installation
Guide