Karcher BD 100-250 R I Bp User Manual
Page 22
-
7
You can make the settings for the different
cleaning programs in the operator menu.
Different parameters can be set based on
the cleaning program. The settings are
done using the Info button.
Release emergency-stop button by
turning.
Sit on the seat and set main switch to
“1”.
The display shows the battery charging
status and the fresh water level.
Select cleaning program.
Call the operator menu by turning the
info button.
Select the desired parameter by turning
the Info button. The currently set value
is displayed as a bar.
Press Info button, the bar display
blinks.
Reset the parameter by turning the Info
button between "min" and "max".
Accept modified setting by pressing the
Info button or wait till the set value is ac-
cepted automatically.
Note
If the selected parameter does not change
within 10 seconds, then the display goes
back to displaying the battery charging sta-
tus and the fresh water level.
The same cleaning parameter can have in-
dividual settings for each cleaning pro-
gram.
The brush pressure can be set only when
the machine is on in the programs brush
suction, wet brushing, polishing and polish-
ing suction.
All settings are saved in the powerless
state of the machine.
Select the menu item "Accept default
values?" in the operator menu by turn-
ing the Info button
Press Info button. The factory settings
of all parameters are restored for each
cleaning program.
The table given below gives details of the
factory settings of the parameters for the
cleaning programs. If no values are en-
tered, then the respective parameter can-
not be set in the given cleaning program.
To improve the vacuuming result on tiled
floors the vacuum bar can be turned to an
oblique position of up to 5°.
Release the wing nuts.
Turn the vacuum bar.
Tighten the wing nuts.
If the vacuum result is unsatisfactory the in-
clination of the straight vacuum bar can be
modified.
Release the wing nuts.
Tilt the vacuum bar.
Tighten the wing nuts.
–
During normal operations (fresh water
mode), water is taken from the fresh
water tank and collected in dirt water
tank after use.
–
Water can be circulated for floors with
dirt levels of slight to normal.
First clean in the fresh water mode till
the water in the fresh water tank has
been consumed.
The set the switching of recyling/ fresh
water mode to Recycling.
Note
–
The dirt water is cleaned by a filter be-
fore being reused.
–
For recycling operations, the entire re-
cycling filter must lie below the dirt wa-
ter level.
Caution
Risk of damage due to overdose of deter-
gent. Very often, the detergent contained
in the dirt water has only been partially
used. Hence, in the recycling mode, the
detergent quantity to be added is to be set
to 0.
Note
Overflow dirt water tank. If the dirt water
tank is full, the suction turbine switches off
and the indicator lamp "dirt water tank full"
begins to blink. All cleaning programs with
suction are blocked for one minute. Empty
the dirt water reservoir.
ṇ
Warning
Please observe the local provisions regard-
ing the wastewater treatment.
Take the fresh water drain hose or the
dirt water drain hose from the support
and lower it into a suitable collection de-
vice.
Settings
Operations menu
Reset parameters
Adjustable
parameters
min:step:m
ax
Remark
Water quantity 1:1:8
0=min.,
8=max.
Detergent dos-
ing unit
0:1:5
0=Off,
1=min.,
5=max.
Brush pres-
sure
0:1:8
0=min.,
8=max.
FACT (brush
speed)
–
Power-,
Whisper-,
Fine Clean
SUCTION
(suction per-
formance)
–
Mode:
POWER,
Mode:
WHISPER
Brush rotation
time after stop
0s:1s:3s
From idling
to lifting
Working speed 1:1:6
1=1km/h,
6=6km/h
Only for BR/BD...RI models:
Trailing time
for sweeper af-
ter stopping
0s:1s:3s
From idling
to lifting
Factory setting BR...:
Water quantity
Detergent dosing
Brush pressure
FACT (brush speed)
SUCTION
Brush trailing time (s)
Working speed
Trailing time for sweeping
Driving
– – – – – – – 2
Scrubbing
suction
5 0 4 p p 2 4 –
Wet scrub-
bing
5 0 4 p – 2 4 –
Dry vacu-
um cleaning
– – – – p – 4 –
Polishing
– – 4 p – 0 4 –
Polish suc-
tion
– – 4 p p 0 4 –
Manual
cleaning
– – – – – – – –
P=Power Clean
Setting the Vacuum Bar
Oblique position
Inclination
Recycling operations (option)
Empty tanks.
22
EN