Horner APG RCX HE-CX251 User Manual
Page 2
MAN0920-01-EN
Specifications / Installation
__________________________________________________________________________________________________________________________________________________________________
9/1/2010
Page 2 of 2
3
Wiring
4
Safety
5
Technical Support
For assistance and manual updates, contact Technical Support at the
following locations:
North America:
(317) 916-4274
http://www.heapg.com
email:
Europe:
(+) 353-21-4321-266
http://www.horner-apg.com
email:
.
Warning: Consult
user documentation.
Warning: Electrical
Shock Hazard.
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or Non-hazardous locations only
WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability for Class I, Division 2
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CE MATERIAL INACCEPTABLE POUR LES EMPLACEMENTS DE
CLASSE 1, DIVISION 2
WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE DECONNECTOR L'EQUIPMENT, COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST
DESIGNE NON DANGEREUX.
WARNING: To avoid the risk of electric shock or burns, always connect the safety (or earth) ground before making any other connections.
WARNING: To reduce the risk of fire, electrical shock, or physical injury it is strongly recommended to fuse the voltage measurement inputs. Be sure to locate fuses as close to
the source as possible.
WARNING: Replace fuse with the same type and rating to provide protection against risk of fire and shock hazards.
WARNING: In the event of repeated failure, do not replace the fuse again as a repeated failure indicates a defective condition that will not clear by replacing the fuse.
WARNING: Only qualified electrical personnel familiar with the construction and operation of this equipment and the hazards involved should install, adjust, operate, or service
this equipment. Read and understand this manual and other applicable manuals in their entirety before proceeding. Failure to observe this precaution could result in severe
bodily injury or loss of life.
When found on the product, the following symbols specify:
All applicable codes and standards need to be followed in the installation of this product.
Adhere to the following safety precautions whenever any type of connection is made to the module:
Connect the safety (earth) ground on the power connector first before making any other connections.
When connecting to electric circuits or pulse-initiating equipment, open their related breakers.
Do not make connections to live power lines.
Make connections to the module first; then connect to the circuit to be monitored.
Route power wires in a safe manner in accordance with good practice and local codes.
Wear proper personal protective equipment including safety glasses and insulated gloves when making connections to power circuits.
Ensure hands, shoes, and floor are dry before making any connection to a power line.
Make sure the unit is turned OFF before making connection to terminals.
Make sure all circuits are de-energized before making connections.
Before each use, inspect all cables for breaks or cracks in the insulation. Replace immediately if defective.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
No part of this publication may be reproduced without the prior agreement and written permission of Horner APG, Inc. Information in this document is
subject to change without notice
Pin
MJ1 / MJ2 Pins
Signal
Direction
8
TXD
OUT
7
RXD
IN
6
0 V
Ground
5*
+5 60mA
OUT
4
TX-
OUT
3
TX+
OUT
2
RX-
IN
1
RX+
IN
1
8
Power Connector: 10-30Vdc
Torque Rating: 4.5-7.0 Lb-In
(0.50-0.78 N-m)
CsCAN: self-powered
Comms DIP Switch
1.
RS-485 Termination
2.
RS-485 Half-Duplex Mode
3.
RS-485 Half-Duplex Mode
4.
CAN Baud Rate
5.
CAN Baud Rate
CAN baud-rate settings (sw 4&5)
00
125kbaud
01
250kbaud
10
125kbaud
11
250kbaud
Serial Ports: 2 ports on 1 connector
MJ1 RS-232 (pins 6, 7, 8)
MJ2 RS-422 (pins 1, 2, 3, 4, 6)
MJ2 RS-485* (pins 1, 2, 6)
*set DIP switches 2 & 3 for RS-485