Red Lion CUB5 - Manual (Page 7)

7
6.1 Module 1 - i
nput
S
etup
p
araMeterS
(
1-INPUt
)
COUNTER A DECIMAL POSITION
COUNTER A SCALE FACTOR
The number of input counts is multiplied by the scale factor to obtain the
desired process value. A scale factor of 1.0000 will result in the display of the
actual number of input counts. (Details on scaling calculations are explained at
the end of this section.)*
This selects the decimal point position for Counter A. The selection will also
affect Counter A scale factor calculations.
00.0001 to 99.9999
COUNTER RESET AT POWER-UP
yES
NO
COUNT MODE
Select the count mode that corresponds with your application. The input
actions are shown in the boxes below. For simple counting applications, it is
recommended to use Count with Direction for the count mode. Simply leave the
direction input unconnected.
COUNTER B DECIMAL POSITION
This selects the decimal point position for Counter B. The selection will also
affect Counter B scale factor calculations.
COUNTER B SCALE FACTOR
The number of input or batch counts is multiplied by the scale factor to
obtain the desired process value. A scale factor of 1.0000 will result in the
display of the actual number of input or batch counts. (Details on scaling
calculations are explained at the end of this section.)*
00.0001 to 99.9999
Count b NO
both A-b Count A
Cnt ud qUAd 1 Add Add
dUAL Cnt
RAtE Cnt
qUAd 4
qUAd 2 Add Sub
0.00000 0.000 0.0
0.0000 0.00 0
0.00000 0.000 0.0
0.0000 0.00 0


Cnt ud
INP A-b


0
CntA dP


01.0000
CmtA ScF
COUNTER A COUNT LOAD VALUE
Counter A resets to this value if Reset to Count Load action is selected.
-9999999 to 99999999


00000500
CmtA Ld
COUNTER B BATCH COUNT ENABLE
The Counter B batch count function internally counts the number of output
activations of the selected setpoint(s). The count source for the batch counter
can be SP1, SP2 or both. Batch counting is available in all count modes except
Dual Counter, which uses an external input signal for Counter B. This
parameter only appears if a Setpoint Output option card is installed.


NO
Cmtb bAt


0
Cntb dP


01.0000


NO
RSt P-UP
Shaded area selections only apply when Counter B is enabled (Dual Counter
mode or batch counter).
Counter A Subtract Counter A Add
Counter A Add Counter A Add
Quad A Count A
Quad A Count A
Quad A Count A
Counter B Add Counter A Add
Counter A Add Rate only
Counter A Direction Counter A
INPUT B ACTION INPUT A ACTION
Add Sub 2 Input Add/Subtract
Add Add 2 Input Add/Add
qUAd 4 Quadrature x4
qUAd 2 Quadrature x2
qUAd 1 Quadrature x1
dUAL Cnt Dual Counter
RAtE Cnt Rate/Counter
Cnt ud Count with Direction
DISPLAY MODE
The selected counter(s) will reset at each meter power-up.
* For value entry instructions, refer to selection/value entry in the Programming
The Meter section.
Note: The Rate indicator signal is derived from Input A in all count modes.
Cntb ScF
COUNTER A RESET ACTION
When Counter A is reset, it returns to Zero or Counter A Count Load value.
This reset action applies to all Counter A resets, except a setpoint generated
Counter Auto Reset programmed in Module 4.


to 2Ero
CmtA rSt
to 2Ero to CtLd
COUNTER A COUNT DIRECTION
Reverse ( rEV ) switches the normal Counter A count direction shown in the
Count Mode parameter chart.


NOr
CmtA dir
NOr rEV
NO SP2
SP1 SP1-2
Counter A
Decimal Point
Counter A
Scale Factor
User Input
Function
Counter B
Decimal Point
Counter B
Scale Factor
Counter Reset
at Power-up
User Input
Assignment
Count
Mode
SEL Dual Count or Batch
Only
Dual Count
or Batch
Only
INP A-b CntA dP CntA ScF Cntb ScF RSt P-UP USEr INP USEr ASN
1-INPUt Pro
CntA dir
Counter A
Count
Direction
Counter A
Reset Action
CntA rSt CntA Ld
Counter A
Count Load
Value
Counter B
Batch Count
Enable
Cntb bAt Cntb dP
PARAMETER MENU