FUTEK IPM500 (D500) Digital Display - Manual (Page 49)

0 1 Relay1 Off when Al1 active, Relay2 On when Al2 active
1 0 Relay1 On when Al1 active, Relay2 Off when Al2 active
1 1 Relay1 Off when Al1 active, Relay2 Off when Al2 active
00 (U) Serial Cnfg4
(NG to review
carefully)
Bit 7 6 5 4 3 2 1 0 Serial Protocol
1 0 No Parity
1 1 Odd Parity
0 0 Custom ASCII protocol (8 bits)
0 1 Modbus RTU protocol (8 bits)
1 0 Modbus ASCII protocol (7 bits)
0 0 1 s Modbus ASCII gap timeout
0 1 3 s Modbus ASCII gap timeout
1 0 5 s Modbus ASCII gap timeout
1 1 10 s Modbus ASCII gap timeout
11.2 WEIGHT METER 3-BYTE RAM MEMORY DATA (3 Bytes / Item)
MS Mid LS Description
A1
9E
1B
18
9B
98
8F
8C
15
12
89
86
E4
1E
A0
9D
1A
17
9A
97
8E
8B
14
11
88
85
E3
1D
9F
9C
19
16
99
96
8D
8A
13
10
87
84
E2
1C
Analog high value
Analog low value
Deviation Alarm4
Deviation Alarm3
Deviation Alarm2
Deviation Alarm1
Offset value
Scale factor
Setpoint4
Setpoint3
Setpoint2
Setpoint1
Tare value
Valley
11.3 WEIGHT METER NONVOLATILE MEMORY HEX ADDRESSES (2 Bytes / Item)
Please see the 1 Byte RAM Data Table for bit definitions.
Hex Address MS LS
75
74
73
Setup Byte 1
Setpoint4 Diff3 Byte 3
Setpoint4 Diff3 Byte 1
Spare
Setpoint4 Diff3 Byte 2
Setpoint3 Diff3 Byte 3
72
71
70
6F
6E
6D
6C
6B
6A
1D
1C
1B
18
17
16
15
14
13
12
11
10
0F
0E
0D
0C
0B
0A
09
08
07
06
05
04
03
02
01
00
Setpoint3 Diff3 Byte 2
Setpoint4 Byte 3
Setpoint4 Byte 1
Setpoint3 Byte 2
Alarm Config Byte 4
Version
T Stop
Reserved
Reserved
Tare Byte 3
Tare Byte 1
Serial Config Byte 3
Setpoint 2 Diff Byte 3
Setpoint 2 Diff Byte 1
Setpoint 1 Diff Byte 2
Configuration
Analog Setup
Lockout Byte 2
Serial Config Byte 2
Options
Setup
Alarm Config Byte 2
Analog High Byte 3
Analog High Byte 1
Analog Low Byte 2
High Reading Byte 3
High Reading Byte 1
High Input Byte 2
Low Reading Byte 3
Low Reading Byte 1
Low Input Byte 2
Offset Byte 3
Offset Byte 1
Scale Factor 2
Setpoint2 Byte 3
Setpoint2 Byte 1
Setpoint1 Byte 2
Setpoint3 Diff3 Byte 1
Setpoint4 Byte 2
Setpoint3 Byte 3
Setpoint3 Byte 1
Alarm Config Byte 3
M Type
T Start
Reserved
Reserved
Tare Byte 2
Spare
Count Byte 1
Setpoint 2 Diff Byte 2
Setpoint 1 Diff Byte 3
Setpoint 1 Diff Byte 1
SC Type (do not change)
System Decimal Point
Lockout Byte 1
Serial Config Byte 1
Filter
Input Type
Alarm Config Byte 1
Analog High Byte 2
Analog Low Byte 3
Analog Low Byte 1
High Reading Byte 2
High Input Byte 3
High Input Byte 1
Low Reading Byte 2
Low Input Byte 3
Low Input Byte 1
Scale Factor Byte 3
Scale Factor Byte 3
Scale Factor Byte 1
Setpoint2 Byte 2
Setpoint1 Byte 3
Setpoint1 Byte 1
49