Detcon 1600A-N1R - Manual (Page 29)

1600A-N1R
1600A-N1R Instruction Manual Rev. 0.1 Page 25 of 38
Bit 3 1 = Channel 4 Alarm 2 0 = Channel 4 no Alarm 2
Bit 2 1 = Channel 3 Alarm 2 0 = Channel 3 no Alarm 2
Bit 1 1 = Channel 2 Alarm 2 0 = Channel 2 no Alarm 2
Bit 0 1 = Channel 1 Alarm 2 0 = Channel 1 no Alarm 2
40019 Alarm 3 Status Bits
High Byte
Bit 7
1 = Channel 16 Alarm 3 0 = Channel 16 no Alarm 3
Bit 6 1 = Channel 15 Alarm 3 0 = Channel 15 no Alarm 3
Bit 5 1 = Channel 14 Alarm 3 0 = Channel 14 no Alarm 3
Bit 4 1 = Channel 13 Alarm 3 0 = Channel 13 no Alarm 3
Bit 3 1 = Channel 12 Alarm 3 0 = Channel 12 no Alarm 3
Bit 2 1 = Channel 11 Alarm 3 0 = Channel 11 no Alarm 3
Bit 1 1 = Channel 10 Alarm 3 0 = Channel 10 no Alarm 3
Bit 0 1 = Channel 9 Alarm 3 0 = Channel 9 no Alarm 3
Low Byte
Bit 7
1 = Channel 8 Alarm 3 0 = Channel 8 no Alarm 3
Bit 6 1 = Channel 7 Alarm 3 0 = Channel 7 no Alarm 3
Bit 5 1 = Channel 6 Alarm 3 0 = Channel 6 no Alarm 3
Bit 4 1 = Channel 5 Alarm 3 0 = Channel 5 no Alarm 3
Bit 3 1 = Channel 4 Alarm 3 0 = Channel 4 no Alarm 3
Bit 2 1 = Channel 3 Alarm 3 0 = Channel 3 no Alarm 3
Bit 1 1 = Channel 2 Alarm 3 0 = Channel 2 no Alarm 3
Bit 0 1 = Channel 1 Alarm 3 0 = Channel 1 no Alarm 3
40020 Cal Status Bits
High Byte
Bit 7
1 = Channel 16 Cal 0 = Channel 16 no Cal
Bit 6 1 = Channel 15 Cal 0 = Channel 15 no Cal
Bit 5 1 = Channel 14 Cal 0 = Channel 14 no Cal
Bit 4 1 = Channel 13 Cal 0 = Channel 13 no Cal
Bit 3 1 = Channel 12 Cal 0 = Channel 12 no Cal
Bit 2 1 = Channel 11 Cal 0 = Channel 11 no Cal
Bit 1 1 = Channel 10 Cal 0 = Channel 10 no Cal
Bit 0 1 = Channel 9 Cal 0 = Channel 9 no Cal
Low Byte
Bit 7
1 = Channel 8 Cal 0 = Channel 8 no Cal
Bit 6 1 = Channel 7 Cal 0 = Channel 7 no Cal
Bit 5 1 = Channel 6 Cal 0 = Channel 6 no Cal
Bit 4 1 = Channel 5 Cal 0 = Channel 5 no Cal
Bit 3 1 = Channel 4 Cal 0 = Channel 4 no Cal
Bit 2 1 = Channel 3 Cal 0 = Channel 3 no Cal
Bit 1 1 = Channel 2 Cal 0 = Channel 2 no Cal
Bit 0 1 = Channel 1 Cal 0 = Channel 1 no Cal
5.6 Firmware Upgrade
The 1600A-N1P is capable of firmware upgrades for both the PLC and touch screen device. Upgrades will be
performed by the user. The following components are needed to perform firmware upgrades:
o ProSave Software (can be Downloaded free at http://www.siemens.com)
o S7-200 USB PPI cable
o S7-200 Memory cartridge
o DB9 Gender Changer