0 troubleshooting sct, Equipped machines, 4 meter rpm chart – Seed Hawk AIRCART 2014 User Manual
Page 42: Helical bean tube (canola)
SEED HAWK
®
2014 AIRCART OPERATOR’S MANUAL
SEED HAWK
®
2014 AIRCART OPERATOR’S MANUAL
76
Application Rate (lbs/ac)
25
50
75 100 125 150 175 200 225 250 275 300
Drill Width
(ft)
40
3
6
9
12
15
18
21
24
27
30
33
36
50
4
8
11
15
19
23
27
30
34
38
42
45
60
5
9
14
18
23
27
32
36
41
45
50
55
66
5
10
15
20
25
30
35
40
45
50
55
60
72
5
11
16
22
27
33
38
44
49
55
60
65
80
6
12
18
24
30
36
42
48
55
61
67
73
84
6
13
19
25
32
38
45
51
57
64
70
76
Application Rate (lbs/ac)
25
50
75 100 125 150 175 200 225 250 275 300
Drill Width
(ft)
40
5
10
15
20
25
30
36
41
46
51
56
61
50
6
13
19
25
32
38
44
51
57
63
70
76
60
8
15
23
30
38
46
55
64
41
45
50
55
66
5
10
15
20
25
30
35
40
45
50
55
60
72
5
11
16
22
27
33
38
44
49
55
60
65
80
6
12
18
24
30
36
42
48
55
61
67
73
84
6
13
19
25
32
38
45
51
57
64
70
76
Application Rate (lbs/ac)
2
4
6
8
10
12
14
16
18
20
22
24
Drill Width
(ft)
40
4
9
13
17
21
26
30
34
39
43
47
51
50
5
11
16
21
27
32
37
43
48
53
59
64
60
6
13
19
26
32
39
45
51
58
64
71
77
66
7
14
21
28
35
42
49
56
64
71
78
85
72
8
15
23
31
39
46
54
62
69
77
85
92
80
9
17
26
34
43
51
60
68
77
86
94 103
84
9
18
27
36
45
54
63
72
81
90
99 108
8.4 Meter RPM Chart
Helical
Bean
Tube (Canola)
NOTE: Installing a roller is
often easier with the front
cleanout door removed. This
reduces the chance of the
roller binding on any residual
product that remains below
the product gates after they
have been shut.
77
9.0 Troubleshooting SCT
®
Equipped Machines
Possible Cause
Solution
No hydraulic pressure to
meter block.
Engage hydraulic circuit (Opener).
BFJ (pressure relief block)
set too low.
Increase pressure (factory set to 1800 psi).
No power at coils.
Turn master switch on.
Check fuses.
Check connections at coil and SCT
®
node.
Possible Cause
Solution
No hydraulic pressure.
Engage hydraulic circuit (wing down).
Master switch on.
Turn master switch off (unfold only).
Gates will not open/close
Openers will not lift
Wing down switch will not work
Possible Cause
Solution
No hydraulic pressure to
meter block.
Engage hydraulic circuit (wing down).
Check green banded hydraulic connections at
drill and tractor to ensure they are properly
engaged and/or failed.
Check SCT
®
node.
Check lights on front of node.
Meter block PRV (pressure
relief valve) set to low.
Increase PRV pressure until gates cycle (do not
exceed 500 psi).
No power at coils.
Turn master switch on.
Check fuses.
Check connections at coil and SCT
®
node.
Possible Cause
Solution
Improper look aheads.
Ensure that the look ahead number is not a
negative number.
Aggressiveness set too
high.
Turn aggressiveness off.
Improper drill setup.
Wrong drill and tractor measurements in Viper
Pro™ check and adjust settings as required
Random Opener Sections Lifting