DoorKing 1833 PC Programmable User Manual
Page 37
1835-065-E-7-13
35
The instruction message scrolls across the screen from right to left when the system is not in use and
follows the user message programmed in 3.4.2. The instruction message can be a maximum of 52
characters (spaces count as a character) and is entered into the system memory in three blocks. The
first two blocks contain 20 characters while the third block contains 12 characters. The example below
shows how the sample instruction message was divided into three blocks and programmed into the
system. Use the blank table to organize your own message. Only upper case letters, numbers and spaces
can be programmed from the system keypad.
Factory Default Instruction Message: Push A-Z To Find Name Or No. Enter Code Or Push Call
After organizing the instruction message in the table above, follow the instructions below to enter the message into the system.
After each desired letter, number or space is displayed on the directory, remember to press
*
to enter that character. Spaces
count as a character and must be entered into memory as a character. After a complete block of characters (including spaces)
has been entered, press
*
to enter the block, then start the next block.
Note: The factory default message was programmed from a PC, therefore upper and lower case letters are displayed.
Example: PUSH A OR Z BUTTON TO FIND NAME ENTER CODE OR PUSH CALL
Block 1
Block 2
Block 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
P
U
S
H
A
O
R
Z
T
O
F
I
N
D
N
A
M
E
E
N
T
E
R
C
O
D
E
O
R
P
Block 1
Block 2
Block 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
77
88
99
44
55
66
11
22
33
00
OPER
OPER
WXYZ
WXYZ
TUV
TUV
PQRS
PQRS
MNO
MNO
JKL
JKL
GHI
GHI
DEF
DEF
ABC
ABC
SP
SP
CALL
Z
A
TELEPHONE ENTRY SYSTEM
HOLD TO SCAN
OPERATING INSTRUCTIONS
Use “A to Z” Buttons to Locate
Name and Code Number on Display.
Names are In Alphabetical Order.
To Call, Enter Code Number on
Keypad or Press “Call” Button. If
Line is Busy, Press “#” or “Call” to
Hang Up. Try Again.
Enter on Open Display and Tone.
1.
2.
3.
1. Press and enter your four-digit MASTER CODE (beep).
The LCD display on the 1834 and 1835 systems will read: BLOCK 1.
2. Enter the characters into block 1 (refer to 3.4.1 for reference). Remember to press (beep) after each character.
3. After the last character in block 1 has been entered, press (beep) to enter the entire block.
The LCD display will read: BLOCK 2.
4. Enter the characters into block 2. Remember to press (beep) after each character.
5. After the last character in block 2 has been entered, press (beep) to enter the entire block.
The LCD display will read: BLOCK 3.
6. Enter the characters into block 3. Remember to press (beep) after each character.
7. After the last character in block 3 has been entered, press (beep) to enter the entire block.
8. Press (beep) to enter all three blocks into the system memory.
9. Press together to end this programming sequence (beeeeeep).
10. The new instruction message will begin to scroll across the screen.
??
??
??
??
11
SP
SP
88
TUV
TUV
00
OPER
OPER
3.4.3 Programming the Instruction Message – 1834, 1835 Systems
U
S
H
C
A
L
L