DoorKing 1833 PC Programmable - Manual (Page 24)

1835-065-E-7-13 22
POWER
NC
P1 P2
NO NC NO NC NO
1 ON
2
3
4
5
6
7
8
NC NO
ELEVATOR
16AC 16AC BAT 1NO 1NC 1C 2RY 2C A
1
2
3
Auxiliar
y T
e
rminal
NO NC C
Lock Power
UL listed
Board Power
UL listed
P1: #13 & #14
Board Power
UL listed
P1: #13 & #14
16 VAC
20 VA
POWER
NC
P1 P2
NO NC NO NC NO
1 ON
2
3
4
5
6
7
8
Lock Power
UL listed
Card Reader
P2: #6 - #9 Card Reader
P2: #6 - #9
16 VAC
20 VA
14
15
16
17
18
13
12
11
10
9
8
7
6
5
4
3
2
1
14
15
16
17
18
13
12
11
10
9
8
7
6
5
4
3
2
1
Brown
Brown
Blue
Blue
Ground #12 Ground #12
Blue #17 Red #10 Brown #
8
Blue #17 Red #10 Brown #
8
Black #7 White #
8
Green #9 Black #7 White #
8
Green #9
POWER
NC
P1 P2
NO NC NO NC NO
1 ON
2
3
4
5
6
7
8
Lock Power
UL listed
Board Power
UL listed
P1: #13 & #14
Board Power
UL listed
P1: #13 & #14
16 VAC
20 VA
POWER
NC
P1 P2
NO NC NO NC NO
1 ON
2
3
4
5
6
7
8
Lock Power
UL listed
Card Reader
P2: #6 - #9
Card Reader
P2: #6 - #9
16 VAC
20 VA
14
15
16
17
18
13
12
11
10
9
8
7
6
5
4
3
2
1
14
15
16
17
18
13
12
11
10
9
8
7
6
5
4
3
2
1
Ground #12 Ground #12
Blue #17 Red #10 Brown #
8
Blue #17 Red #10 Brown #
8
Black #7 White #
8
Green #9 Black #7 White #
8
Green #9
12
34
5
6
7
8
9
10
11
12
13
14
Door Lock
or Gate
Operator
P1: #5
Door Lock
or Gate
Operator
P1: #5
Door Lock
or Gate
Operator
P1: #5
Door Lock
or Gate
Operator
P1: #5
14
13
12
11
10
9
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Main Terminal
Wiring these telephone entry systems are the same as section 2.3.1 EXCEPT for the expansion board connection. From 9 to 16
boards can be wired. The FIRST 8 boards MUST connect from #7 thru #9 on the aux terminal. Boards 9 to 16 MUST connect
from #11 thru #13 on the aux terminal. All expansion boards MUST have their own power source. See the Expansion Board
Manual 2351-065 for further information BEFORE wiring expansion boards.
2.3.3 Wiring 9 to 16 Expansion Boards - 1833, 1835 and 1837 Systems
Expansion Board 9
Expansion Boards 9 to 16
Telephone
Entry System
Circuit Board
Expansion Boards 1 to 8
Expansion Board 10
To Expansion
Boards
11 thru 16
Connect expansion boards using 6 conductor,
stranded with overall shield. 18, 20, 22 or 24
gauge. Shield runs continuous. Float the
shield, DO NOT connect shield to 2351-010
board common.
Expansion Board Power: You may power up to four (4) expansion
boards from a single 16 VAC, 20 VA power transformer.
18 AWG wire up to 100 Ft.
16 AWG wire up to 200 Ft.
It is advisable to keep power wire runs as short as possible.
Connect card reader using 4
conductor, stranded with overall
shield. 18, 20, 22 or 24 gauge.
Relay 1 Input
Relay 2 Input
“2RY” Contact is set NO with Relay 2 Jumper on board.
Red - NO circuit board connection.
Battery Back-up power connection - optional.
Red - NO circuit board connection.
Aux Terminal Connection 9 to 16
Black - Aux #13 connection.
White - Aux #12 connection.
Green - Aux #11 connection.
Aux Terminal Connection 1 to 8
Black - Aux #9 connection.
White - Aux #8 connection.
Green - Aux #7 connection.
Expansion Board 1 Expansion Board 2
To Expansion
Boards 3 thru 8
Relay 2 Jumper
The model 2351 Expansion Board allows you to expand the
number of remote entry points that the 1833, 1835, 1837
telephone entry systems can control up to 16. One expansion
board is required for EACH remote entry point. Two sets of 8
boards get wired to the entry systems circuit board.
1833, 1835 & 1837 Systems
with Up to 16 expansion
boards connected:
Control 1 entry point (Relay 0) with system circuit board.
Control up to 16 more remote entry points with expansion
boards.
Note: Separate elevator control board required for elevator
control.
NC
NO
Relay 0
• Maximum wire run between Expansion boards 1-8 is 500 feet total.
• Do not use twisted pair wire with weigand output format.
• Proper grounding is required! Ground wire should be a minimum 12 AWG.
• Maximum wire run between Expansion boards 9-16 is 500 feet total.
• Do not use twisted pair wire with weigand output format.
• Proper grounding is required! Ground wire should be a minimum 12 AWG.
System Relays
11-18
System Relays
3-10
Connect expansion boards using 6 conductor, stranded with overall
shield. 18, 20, 22 or 24 gauge. Shield runs continuous. Float the
shield, DO NOT connect shield to 2351-010 board common.