Draw-Tite 118618 T-ONE CONNECTOR - Manual

WARNING
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
9. Reconnect the vehicle’s Negative (-) battery
cable and install the 15 amp fuse into the fuse
holder from step 8.
WARNING
All connections must be complete for the
T-One ® T-Connector to function properly.
Test and verify installation with a test light
or trailer once installed. For initial test, reset
vehicle electrical system by temporarily
removing the key from the ignition.
10. Secure the remainder of the T-One ® T-Connector
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid
any areas that would pinch, cut or melt the wire.
11. Reinstall the threshold, storage covers,
floor covering and other items removed during
installation, being careful not to pinch or cut
the wires.
NOTE
Store 4-Flat connector in rear cargo area when
not in use.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of vehicle manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual & instruction sheet
for additional information.
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, Drill (3/32” Drill Bit),
1/4” Socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open rear door and remove the access panel
doors on both sides to access vehicle’s wiring
connectors d. Several trim panel fasteners will
need to be removed to remove the panels e.
2. There will be connection points matching the
ends of the T-One ® T-Connector adapter on the
back of each of the vehicle taillight housings.
Disconnect the wire harness.
3. Beginning on the driver’s side, plug the T-One ®
T-Connector harness containing the yellow wire
in between the vehicle’s mating connectors.
NOTE
Be careful not to damage the locking tabs and
be sure that connectors are fully inserted with
locking tabs in place.
4. On the Driver’s side route the T-One ® T-Connector
end with the green wire up through the trim panel
access hole, across the top threshold, & through
the passenger trim panel access hole f. Repeat
step 2 & 3 for the passenger’s side using the
T-Connector containing the green wire.
NOTE
For ease of installation attach harness
(two connectors) to fish wire and carefully
pull toward passenger side.
5. Locate a suitable grounding point on the driver’s
side near the connectors. Drill a 3/32” hole
and secure white wire with eyelet using screw
provided. Do not drill into any exposed surfaces.
CAUTION
Verify what is behind any surface prior to drilling
to avoid damage to the vehicle and/or personal
injury. Do not drill into any exposed surfaces.
6. On the Driver’s side, mount the T-One ®
T-Connector black box using the double-sided
tape provided. Secure the remainder of the
T-One ® T-Connector harness with the cable ties
provided, to prevent damage or rattling and
being careful to avoid any areas that would
cut or pinch the wire.
WARNING
Make sure module is mounted so that the
epoxy side of the module is pointed towards
the ground to prevent any water buildup.
7. On the driver’s side, locate the black 12 ga.
Power wire from the T-One ® T-Connector box.
Attach the black 12 ga. wire provided. Either
route the black wire thru a grommet and along
the exterior frame or follow the existing wiring
along the thresholds into the engine compartment
up to the battery avoiding areas that may pinch
or break the wire g.
8. Disconnect the vehicle’s Negative (-) battery
cable. If not removed, remove the fuse from the
yellow fuse holder (provided). After cutting the
fuse holder wire h, attach the ring terminal and
secure to the vehicle’s Positive (+) battery cable.
Connect the other end of the fuse holder to
the black 12 ga. wire, using the yellow butt
connector (provided) i.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-One ® T-Connector
T-One ® Connecteur en T
T-One ® Conector en T
Ram Promaster
118618-037 Rev. A 12/3/13
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
PAGE 1 OF 3
f
g
h e
i
d