Extron Electronics PVS 305SA User Guide - Manual (Page 37)

4-9 PVS 305SA • Serial Communication
PRELIMINAR
Y
PRELIMINAR
Y
N
X@ = Status: 1 = dual mono, 2 = stereo
X# = Status: 0 = off/disable (default), 1 = on/enable
X1) = Power amp gain, -10 through +10 dB (default = 0)
X1@ = Power amp attenuation, 0 -20, (+/-10 dB in 1 dB steps)
X2@ = RGB delay (0 to 5 seconds), in 0.5 second intervals: 0 = 0 seconds, 1 = 0.5 seconds....10 = 5.0 seconds.
X2% = Mic talk-over threshold range: 0 to 15 (default = 6)
X2^ = Program ducking level: 0 to 30 (default = 15)
X2& = Lineout status: 1= variable, 2 = fixed, 3 = independent (separate mono Left channel fixed and mono right
channel variable)
X2( = Paging delay, in 1 second steps, 0-8, (default = 0, disabled)
Command/response table for special function SIS commands
The syntax for setting a special function is __ * X? #, where __ is the function number and X? is the value. To view
a function’s setting, use __#, where __ is the function number. In the following table the values of the X? variable
are different for each command/function. These values are given below the tables.
Command ASCII command
(host to processor)
Response
(processor to host)
Additional
description
RGB delay
Set RGB delay 3* X2@ # RGBDly*
X2@] Set RGB delay (in seconds).
View RGB delay 3# RGBDly*
X2@] View RGB delay setting.
Mic talk-over threshold
Adjust talk-over threshold 2* X2% # Thr X2%] Set talk-over threshold.
Increment threshold +*2# Thr
X2%] Increase threshold.
Decrement threshold -*2# Thr X2%] Decrease threshold.
View Mic talk-over threshold 2# Thr
X2%] View talk-over threshold.
Program audio ducking level in talk-over mode
Adjust audio ducking level 58* X2^ # Adl
X2^] Set audio ducking level.
Increment level +*58# Adl
X2^] Increase level.
Decrement level -*58# Adl
X2^] Decrease level.
View audio ducking level 58# Adl X2^] View audio ducking setting.
Lineout mode
Set lineout to variable 55*1# LineOut*
X2&] Set lineout to variable mode.
Set lineout to fixed 55*2# LineOut* X2&] Set lineout to fixed mode.
Set lineout to independent 55*3# LineOut*
X2&] Set lineout to separate mono
Left channel fixed and mono
Right channel variable.
View lineout mode 55# LineOut*
X2&] View lineout mode.
Audio output mode
Set audio output mode to dual
mono 18*1# PreAmpMod*
X@] Sets output to dual mono.
Set output mode to stereo 18*2# PreAmpMod*
X@] Sets output to stereo.
High pass filter mode
Set high pass filter mode off 79*0# Hpf*
X#] Turn high pass filter off.
Set high pass filter mode on 79*1# Hpf*
X#] Turn high pass filter to on.
Loudness control
Set loudness off 29*0# Loudness*
X#] Turn loudness control off.
Set loudness on 29*1# Loudness* X#] Turn loudness control on.
View loudness control setting 29# Loudness*
X#] Show loudness control setting
Power amp gain/attenuation
Set attenuation (-dB) 56* X1@ # AmpLimit*
X1)] Set attenuation level.
View input gain 56# AmpLimit*
X1)] View input gain.
Paging sensor delay
Set paging sensor delay 75* X2( # PageDly*
X2(] Set delay time.
View paging sensor delay 75# PageDly* X2(] View delay time.