S&B Filters Cold Air Intake Kit - Cotton Filter 75-5068 User Manual
Installation instructions, Vehicle application, Tools required
1.
With the ignition switched off and the
parking brake set, disconnect the negative
battery cables on both batteries.
Installation Instructions
Vehicle Application
Year: 2013 - 2014
Make: Ram
Model: 2500/3500 Diesel
Engine: 6.7L Cummins
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 -
4.
Loosen the hose clamp at the turbo inlet,
next pinch the spring clamp and slide it up the
steel piping. Then disconnect the silicone
hose from the steel piping and remove spring
clamp.
8.
Disconnect the factory swing gate motor
connector that is located on the side of the
factory air box. Press in the locking button on
the connector and pull out.
2.
Disconnect the electrical connection for the
Intake Air Temp. (IAT) Sensor and the Mass Air
Flow (MAF) Sensor then unsnap the wire loom
from the tube. (See the next step for removal)
6.
Remove factory retaining bolt on the front of
the factory air box. Once retaining bolt is
removed disconnect hose clip by pulling up and
then move hose forward to help remove air box.
(See Below)
9
. Once the swing gate motor is
disconnected completely remove the factory
air box and intake tube by lifting up and out.
3.
For the MAF sensor, slide the
red
locking
tab up then depress the black lever while
disengaging the connector. For the IAT
sensor just depress the
grey
lever while
disengaging the connector.
7.
Lift up on factory air box, be careful not to
remove the whole box because the swing gate
motor harness is still connected on the side of the air
box. Remember to move the hose forward from Step
6 when pulling out the box.
5.
Loosen the hose clamp on the intake
tube to assist with the removal of the air box.
P/N: 75-5068 / 75-5068D
SEE EXPLODED VIEW ON PAGE 7
1
Tools Required
• 7mm, 8mm, 10mm,& 13mm Wrench & Socket
• 1/8” Allen Key (Supplied w/ Kit), 3/16” Allen Key
• T27 Security Torx Wrench
• 5/16” Nut Driver or Flat Blade Screwdriver
• Phillips Screwdriver, Pliers or Channel locks
• 5/16” Drill bit and Drill
• Electrical Tape
• Razorblade
Notes
Kit may not fit with the following
Aftermarket Parts installed:
• Body Lift or Lowering Kit
• Custom Hood
• Intercooler or Turbo upgrades
S&B Filter Maintnance
Cleanable
(KF-1037)
. If the enclosed filter is Red, it came pre-oiled
from the factory. Please visit
for exact oil
amount required after cleaning.
Disposable
(KF-1037D)
. If the enclosed filter is White, it is a
disposable filter and should be discarded once it reaches capacity.
This filter
(does not require oil)
. For more info on S&Bʼs disposable
filter, visit
.
Before You Start
• Please read the entire product guide before proceeding.
• Ensure all components listed on page 4 are present.
• If you are missing any of the components, call customer support
at (909) 947-0015.
• Do not work on your vehicle while engine is hot.
• Make sure the engine is turned off and the vehicle is in Park or
the Parking Brake is set.
CARB Status - Pending
Product will be submitted to Air Resources
Board for approval shortly.
Not legal for use in CA or other states
adopting CA emissions standards See
Page 6 for more info.
Approx. Install Time 3Hrs 00Min
Locking Tab
Lever