Baron Tachometers_MASTER CYLINDER MOUNT for 2" MINI-BULLET TACH Kawasaki Models - Manual

Page: 1 BA-757x-xx
BULLET & MINI-BULLET TACHOMETERS INSTALLATION
GUIDE - Please see appropriate section for your specific
application
Go slowly and follow instructions carefully. The installation is very easy if the
wire color destinations are followed.
Revision: 17.7 - 04/12/2012
Install Time: 30 to 90 Minutes
INCLUDED IN THE KIT:
(1) Chrome Billet Baron Tachometer (Black or White
Face)
(1) Ring Terminal
(1) Double-Crimp Butt Connectors
(3) Piggy-back Spade Connectors
(3) Blue 3M Scotch-Lock Connectors
(3) Spade Connectors
(1) 3-wire BA-7315-50 BARON Tachometer Adapter
(1) LED Control Box (only included with 7-color
Tachometer)
TOOLS REQUIRED:
5/32" Allen Wrench
24" of 20 GA. Wire (Color is irrelevant)
Wire Crimper/Pliers
Electrician Tape
Factory Service Manual
INSTRUCTIONS:
GENERAL WIRING INSTRUCTIONS:
GREEN WIRE provides the RPM count
BLUE or YELLOW wire provides power for the illumination
RED wire provides power to the Tach
BLACK wire is for ground
INSTALLER NOTES: Reference to LED Control Box is only relevant if you are installing a 7-Color Tachometer, otherwise only worry about the wires
from the Tachometer. To determine if your bikes requires this unit and how to determine the negative side of the coil or to determine if your bike
requires the single fire adapter see FAQ page of this document.
GREEN wire to NEGATIVE terminal of coil.
BLACK wires from Tach and LED Control box both to CHASSIS (Ground)
RED wires from Tach and LED Control box both to POSITIVE terminal of coil (or other switched 12 volt source)
BLUE or YELLOW wire from the Tach go to POSITIVE terminal of coil (or other switched 12 volt source)
7-COLOR TACHOMETERS ONLY
WHITE Connector from Tach to White Connector on LED Control Box
BLACK Switch w/RED button plugs into the LED Control Box WIRING NOTE: If you are equipped to solder your connections we recommend you do
so only after first connecting and testing the tachometer for proper operation.
INSTALLER NOTES: On some models the supplied wiring leads may need to be trimmed to fit the bikes connectors. Use the Ring Terminal for all
chassis ground connections. If you mount your Tach high up on the handlebar, or have tall or pullback risers or wide handlebars, you may need to
splice extra wire to each colored wire lead of your Tachometer prior to completing the routing and connection, then trim to appropriate length.
GENERAL MOUNTING INFORMATION
1. Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off-center, you can rotate
Tach face back to vertical (or any position you desire) by first loosening Tach unit's set screw (located in handlebar clamp area of the Bullet housing or
on the underside of the Mini-Bullet housing). Unscrew the housing's bezel (counterclockwise) then rotate the Tach Face to the desired position,
re-tighten the set screw and re-install the bezel.
2. Secure handlebar clamp by first tightening the flat/front dial side of clamp and then the pointed/rear side of clamp until housing does not rotate
under mild pressure. There must be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened.
Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or
fitment may be required. Barons bears no responsibility on installation costs associated with this product.
© 2013 Barons Custom Accessories
5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.baronscustom.com [email protected]