Veris Industries Badger 3000 SERIES Install - Manual (Page 12)

12
USB COMMAND LIST
In the list below, brackets indicate an argument, specify-
ing its type and value range.
For instance [0-18] stands for any number between 0 and
18 (inclusive).
Example:
“display line1 = 1” sets Line 1 of the display to display #1,
which happens to be the totalizer for flow channel 1.
Diagnostics:
id -- show model number & software version
echo [on/off] -- turn on/off interactive command line:
with echo off, this interface is more
amenable to scripting;
it still accepts the same commands.
Any command entered without an “ = “ sign and
variable will display the current setting
Example: Typing “display line1” returns “0”
which is the variable for Flow Rate
read flow [1-2] -- read the current flow on channel
1 or 2 in GPM
read flow [1-2] total -- read the current total flow
on channel 1 or 2 in gallons
DISPLAY CONFIGURATION
display line1 = [0-1] -- set line 1 of the display
display line2 = [0-1] -- set line 2 of the display
0: flow 1 rate
1: flow 1 total
display urate = [0.1-10] -- set the update rate of
the display, in seconds
INPUT CHANNEL CONFIGURATION
flow [1-2] sensor type = [0-4] -- flow sensor type:
0: PulseDI,
1: PulseKFactor,
2: PullupKFactor*
3: SineKFactor*
4: Analog*
flow [1-2] sensor dical k = [x] -- DI-type flow sensor k
flow [1-2] sensor dical off = [x] -- DI-type flow sensor
offset
flow [1-2] sensor kfact = [x] -- K factor for non-DI sensors
flow [1-2] sensor analog units = [0-19] -- flow units for
analog input
flow [1-2] sensor analog range = [0-4] -- current range for
analog input
flow [1-2] sensor analog high = [x] -- flow rate @max cur-
rent
flow [1-2] sensor analog low = [x] -- flow rate @min cur-
rent
flow [1-2] sensor avg = [0-100] -- averaging "time con-
stant", in seconds:
flow [1-2] rate units = [0-19] -- flow (channel) rate units to
display.
0: GPM
1: gal/s
2: gal/hr,
3: Mgal/day,
4: L/s,
5: LPM,
6: L/hr,
7: ft3/s,
8: ft3/min,
9: ft3/hr,
10:m3/s,
11:m3/min,
12:m3/hr,
13:acreft/s,
14:acreft/min,
15:acreft/hr,
16:bbl/s,
17:bbl/min,
18:bbl/hr,
19:Custom
flow [1-2] rate ndigits = [2-10] -- number of decimal
places to show for flow rate
flow [1-2] rate custom label = [string] -- set the label for
custom units
flow [1-2] rate custom conv = [0-100] -- conversion factor
for custom units
flow [1-2] total units = [0-7] -- set the totalizer units to
display.
0: gal,
1: Mgal,
2: L,
3: ft3,
4: m3,
5: acreft,
6: bbl,
7: Custom
RELAY OUTPUT CONFIGURATION
relay [1-5] func = [0-9] -- relay function; relay 5 is the
pulse output
0: Totalizer
1: Alarm
2: Manual Control
relay [1-5] input = [0-8] -- relay input; depends on source
for totalizer:
0: Flow 1 Total
for alarms:
0: Flow 1 Rate
relay [1-5] units = [0-19] -- units on setpoints/rates; de-
pends on src/input
flow units: same as 'flow [1-2] rate units' above
volume units: same as 'flow [1-2] total units'
relay [1-5] manual = [on/off] -- manually set relay on or
off, if in manual mode
relay [1-5] rate = [x] -- totalizer rate
relay [1-5] ctime = [0-10000] -- pulse width in milliseconds
relay [1-4] latch = [on/off] -- turn on/off relay latching
relay [1-4] setpoint = [x]
relay [1-4] releasepoint = [x]
ANALOG OUTPUT CONFIGURATION
analogout [1-2] func = [0-3]
0: Flow rate