Rover 51 - Manual (Page 8)

Powered Walk Behind Mower - CE Part No. 04016218 Rev F © Copyright 10/2005
™
5
Rover Mowers Ltd
ABN 11 000 257 303
ENGLISH
OPERATION (Continued)
GRASS CUTTING AND CATCHING
Refer to and abide to the instructions noted in the safety instructions of this and associated manuals.
WARNING
• Fit the Grass catcher to the mower (refer to the “Setting Up” section).
• Start the engine and set the engine speed to fast (
) on the throttle control.
• Set the desired cut height (refer to “Setting the Cut Height” above).
• Drive the mower forward through the grass until the catcher fills.
• Stop the engine, remove and empty the catcher.
• Repeat the process.
• To maximise the cutting and catching performance it is important to maintain high engine speed, so adjust the mower ground
speed to suit.
• If the grass length or density is excessive (to maintain high engine speed initially) cut the grass at a higher setting, then at the
desired height.
• Replace blades regularly to maintain a sharp cutting edge.
• Keep the mesh in the grass catcher clean to allow the grass catcher to fill properly.
• Keep the underside of the mower deck clean and free of clipping build-up.
SELF PROPELLED OPTION
Using the Self Propelled Transmission
• Start the engine and set the engine speed to fast.
• Push forward on the clutch engagement lever to engage the self-propelled drive to the rear wheels noting that the drive
speed increases as you move the bale closer to the handle bar (refer figure 9).
• Hold the bale at the required drive speed and slow down or speed up as the conditions dictate.
• To disengage the self-propelled drive release the engagement lever and allow it to return to the disengaged position.
Release the self-propelled drive bale and push the machine when changing direction or mowing
in a confined area for safety.
MAINTENANCE
NOTE: The majority of mower problems involve the following problems:
- Dirt or contaminants in the fuel
- Incorrect oil level in the engine
- Blocked, damaged or incorrectly fitted air cleaner
- Incorrectly maintained blades
(Refer to the maintenance section of this and the engine manufacturer’s manual for details.)
• Always ensure equipment is in good working order.
• Do not use any equipment with worn or damaged components.
• Always use genuine Rover replacement parts.
• Never attempt maintenance that is not outlined in this manual. Refer to your nearest authorised Rover Service Dealer.
• Always ensure the engine is stopped and remove the spark plug wire before attempting any maintenance on the mower.
• On Powerstart models remove the key from the ignition before attempting any maintenance on the mower.
• All safety guards, blades, grass catchers and safety labelling must be replaced with genuine Rover parts if worn or damaged.
• Always replace blades and blade fixings in complete sets to maintain balance.
• Remove clipping build-up around the muffler area to prevent a fire hazard.
WARNING
• Refer to and abide to engine manufacturer’s manual.
• Do not allow any dirt or contaminants to enter the fuel tank, oil filler tube, air cleaner housing, carburettor or spark plug hole
when maintaining the engine.
• Ensure there is no clipping build-up in the vents adjacent to the recoil starter. The engine may overheat and be damaged if these
vents are not clear.
• Do not use high pressure cleaners to wash the machine and keep water away from the engine and electrical components.
• If tilting the mower, the engine spark plug must remain uppermost to prevent oil seepage into the air cleaner and/or exhaust.
• To prevent fuel leaking from the tank when tilting the mower ensure the fuel level is low or empty.
• Ensure the mower is dry and clean and stored in a well ventilated area.
CAUTION
9
Powered Walk Behind A4 CE English.indd 30/11/02, 9:51 PM 8
2
Rover Mowers Ltd
ABN 11 000 257 303
ENGLISH
SPECIFICATIONS
•This manual covers several mowers with the following specifications:
- Models 51, 61 - 20” (508mm Cut Width)
- 12 Cut Height Settings
- Model 80 - 22” (560mm Cut Width)
- 15 Cut Height Settings
NB. - Models come with one of a range of engines (refer to the engine manual included in the kit)
- Options are available (and may be included) on the above models e.g.
- Mulch Mowing
- Deflector Mowing
- Remote Air Cleaner
- Powerstart Function
- Self Propelled Function
- etc.
- Details may be included in this manual or on a separate manual included in the Mower Kit.
SETTING UP
•Before using the Mower the following set-ups are required:
ASSEMBLY OF THE GRASS CATCHER
•Locate the catcher handle and align its front lugs with the slots in the top of the catcher and press firmly into position
(refer figure 2).
•Position the catcher top over the catcher bottom, aligning the barbs on the top with the slots in the bottom (refer
figure 2).
•Press firmly down on the catcher top to lock the barbs into slots (refer figure 2).
•Secure the top and bottom halves of the grass catcher together at the front using the two 3/16” screws, washers and
nyloc nuts supplied. Insert the screws from the outside with the washers and nyloc nuts on the inside of the catcher.
FOLDING THE HANDLE
•Locking knobs: by turning these knobs the handle bars can be either locked in the operating position or folded for storage.
•Locking lever: lift the lever to release the handle bars for folding or push the lever closed to lock handle bars in the
operating position. Adjust the tension by turning the lock nut with a 1/2" AF spanner (refer figure 4 A).
Before unfolding the handlebar, ensure the throttle control is in the stopped position (see
“Starting the Engine” section) and activate the operator presence control lever (refer figure
3). Lift the handlebar slowly (as the engine start cord is attached and it will crank the engine)
until the fully erect position is achieved.
ADJUSTING THE HANDLE HEIGHT
•Loosen the two nuts (B) at the base of the handle bars on both sides of the mower using a 1/2" AF spanner (refer figure
4).
•Move the handle bars to the required position and tighten the handle bar nuts.
COMPONENTS
•Ensure that all the following component parts are included in the package (refer figure 1):
- Mower (1 off)
- Kit including: Owners Manual (1 of)
Engine Manual (1 of)
Spark Plug Spanner (1 of)
Screw - 3/16” x 1/2” UNC (2 of)
Nyloc nut - 3/16” UNC (2 of)
Washer - 3/16” x 1/2” flat (2 of)
- Grass catcher bottom (1 of)
- Grass catcher top (1 of)
- Grass catcher handle (1 of - may be loose or fitted to Grass catcher top)
NB. Other accessories may be included in the carton which vary with each model. These items will be covered by a
separate owners manual e.g. Mulch Mowing Kit, Grass Deflector Kit, etc.
•Notify the place of purchase of missing items as soon as possible.
1
2
4
A
3
0OWERED
6218 Fully Imposed.indd 6 28/10/2005 11:33:58 AM