Nortel Networks 8000 Series - Manual (Page 11)

11
Installing a DC Power Supply in an Ethernet Routing Switch 8000 Series Chassis
Figures
Figure 1 8004DC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 2 8005DC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 3 Removing the bottom front bezel from the 8010co chassis . . . . . . . . . . . 28
Figure 4 Removing a power filler panel: 8010co chassis . . . . . . . . . . . . . . . . . . . . 29
Figure 5 Removing a power filler panel: 8006 and 8010 chassis . . . . . . . . . . . . . . 30
Figure 6 Installing a power filler panel: 8010co chassis . . . . . . . . . . . . . . . . . . . . . 31
Figure 7 Installing a power filler panel: 8006 and 8010 chassis . . . . . . . . . . . . . . . 31
Figure 8 Cable stripping requirements for 8004DC . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 9 Cable stripping requirements for 8005DC . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 10 DC power supply power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 11 Inserting the DC power supply: 8010co chassis . . . . . . . . . . . . . . . . . . . . 37
Figure 12 Inserting the DC power supply: 8006 and 8010 chassis . . . . . . . . . . . . . 37
Figure 13 Removing the plastic safety cover from the DC power supply . . . . . . . . . 38
Figure 14 DC power supply input and ground stud location (8004) . . . . . . . . . . . . . 38
Figure 15 DC power supply input and ground stud location (8005) . . . . . . . . . . . . . 39
Figure 16 Attaching the earth ground lead to the ground stud (8004) . . . . . . . . . . . 40
Figure 17 Attaching the earth ground lead to the ground studs (8005) . . . . . . . . . . 41
Figure 18 Attaching the voltage leads to the power supply terminals . . . . . . . . . . . . 41
Figure 19 Tightening the retaining screws on the DC power supply: 8010co chassis 42
Figure 20 Tightening the retaining screws on the DC power supply: 8006 and 8010
chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 21 Replacing the plastic safety cover on the DC power supply . . . . . . . . . . . 43
Figure 22 DC power supply power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 23 DC power supply power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 24 Removing the plastic safety cover from the DC power supply . . . . . . . . . 47
Figure 25 Loosening the retaining screws on the DC power supply: 8010co chassis 48