Siemens Simatic Industrial PC IPC427C User Manual

Siemens Computers

Table of contents

Document Outline

Operating Instructions SIMATIC IPC427C
Legal information
Table of contents
1 Introduction
- 1.1 Preface
- 1.2 Guideline to the Operating Instructions
2 Safety Instructions
- 2.1 General safety instructions
3 Description
- 3.1 Overview
- 3.2 Applications
- 3.3 Features
- 3.4 Windows Embedded Standard 2009
- 3.5 Design
4 Application planning
- 4.1 Transport
- 4.2 Unpacking and checking the delivery unit
- 4.3 Ambient and Environmental Conditions
5 Installing/mounting
- 5.1 Permitted mounting positions
- 5.2 Mounting information
- 5.3 Mounting the device
- 5.4 Mounting on DIN rails
- 5.5 Mounting with mounting brackets
- 5.6 Upright mounting
6 Connecting
- 6.1 Connecting peripheral equipment
- 6.2 Connecting the 24 V DC power supply
- 6.3 Protective ground connection
- 6.4 USB strain-relief
7 Commissioning
- 7.1 Note before commissioning
- 7.2 Commissioning - Windows Embedded Standard 2009
  - 7.2.1 Basic commissioning - initial startup
- 7.3 Commissioning - Windows XP Professional
  - 7.3.1 Basic commissioning - initial startup
  - 7.3.2 Setting up the language selection for Windows XP Professional / Embedded Standard
- 7.4 Commissioning - other operating systems
  - 7.4.1 Commissioning - guide
8 Integration into an Automation System
- 8.1 Overview
9 Functions
- 9.1 Monitoring Functions
- 9.2 Enhanced Write Filter (EWF)
- 9.3 File Based Write Filter (FBWF)
- 9.4 SRAM buffer memory
- 9.5 Battery monitoring
- 9.6 Operation without monitor and keyboard
10 Expansions and Configurations
- 10.1 Open the device (front panel)
- 10.2 Memory expansion
  - 10.2.1 Installing the memory module
- 10.3 Installing PCI-104 / PC/104 Plus modules
  - 10.3.1 Notes on the modules
  - 10.3.2 Mounting PCI-104 or PC/104 Plus modules
- 10.4 Installing/Removing Compact Flash Cards
11 Maintenance and Service
- 11.1 Removing and Installing Hardware Components
- 11.2 Reinstalling the operating system
  - 11.2.1 Windows Embedded Standard 2009
    - 11.2.1.1 General installation procedure
    - 11.2.1.2 Restoring the software to factory state using the Restore DVD
  - 11.2.2 Windows XP Professional
- 11.3 Partitioning data media
  - 11.3.1 Setting up the partitions under Windows Embedded Standard 2009
  - 11.3.2 Setting up the partitions under Windows XP Professional
- 11.4 Installing drivers and software
  - 11.4.1 Driver installation under Windows Embedded Standard 2009
  - 11.4.2 Installing drivers and software
- 11.5 Installing updates
- 11.6 Data backup
  - 11.6.1 Creating an image
12 Alarm, error and system messages
- 12.1 Boot error messages
13 Troubleshooting/FAQs
- 13.1 General problems
- 13.2 Problems when using modules of third-party manufacturers
14 Technical specifications
- 14.1 General specifications
- 14.2 Power requirements of the components
- 14.3 Integrated DC power supply
15 Dimension drawings
- 15.1 Overview of the dimensional drawings
- 15.2 Dimension drawings of the device
- 15.3 Dimension drawings of the device with mounting brackets
- 15.4 Dimensional drawings of the device with vertical mounting angles
- 15.5 Dimensional drawings of the device with expansion frames
- 15.6 Dimension drawing of the blanking plate
16 Detailed descriptions
- 16.1 Internal components
- 16.2 BIOS Setup
- 16.3 System resources
  - 16.3.1 Currently allocated system resources
  - 16.3.2 System resources used by the BIOS/DOS
    - 16.3.2.1 PCI-Interrupt Lines
- 16.4 I/O Address Areas
A Appendix
- A.1 Guidelines and declarations
- A.2 Certificates and approvals
- A.3 Service and support
B ESD Guidelines
C List of abbreviations
Glossary
Index
- 2
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- O
- P
- R
- S
- T
- U
- V
- W