Jaguar S-TYPE 2004 - Manual (Page 66)

The following abbreviations are used to represent values for Control Module Pin-Out data
I Input PG Power Ground C CAN Network D Serial and Encoded Data
O Output SS Sensor / Signal Supply V S SCP Network V Voltage (DC)
B+ Battery Voltage SG Sensor / Signal Ground D2 D2B Network PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to aid the user in understanding circuit oper ation. THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted. Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE: June 2002
Fig. 05.2
COMPONENTS
Component Connector(s) Connector Description Location
CLUTCH PEDAL POSITION SENSOR CA287 6-WAY / BLACK TOP OF CLUTCH PEDAL
ELECTRONIC PARKING BRAKE SWITCH CA243 8-WAY / BLACK CENTER CONSOLE
GENERAL ELECTRONIC CONTROL MODULE FH9 22-WAY / BLACK LH ‘A’ POST
CA24 26-WAY / NATURAL
CA31 20-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
NEUTRAL SWITCH GB4 2-WAY / BLACK TRANSMISSION, LH REAR
PARKING BRAKE CONTROL MODULE CA241 4-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR
CA242 12-WAY / BLACK
PARKING BRAKE MOTOR CA269 6-WAY / GREY REAR SUSPENSION SUBFRAME
VARIABLE ASSIST STEERING ACTUATOR FH16 2-WAY / BLACK STEERING RACK PINION HOUSING
HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location Location
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
GROUNDS
Ground Location
CA141 UNDER LH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE GENERAL ELECTRONIC CONTROL MODULE (FORWARD OF CA30)
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT.
CONTROL MODULE PIN-OUT INFORMATION
Parking Brake Control Module
Pin Description and Characteristic
B+ CA241-1 BATTERY POWER SUPPLY: B+
O CA241-2 PARKING BRAKE MOTOR ENGAGE: ACTIVATE = B+
O CA241-3 PARKING BRAKE MOTOR DISENGAGE: ACTIVATE = B+
PG CA241-4 POWER GROUND: GROUND
S CA242-1 SCP +
I CA242-3 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA242-4 PARKING BRAKE MOTOR POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
I CA242-5 PARKING BRAKE SWITCH – APPLY: CHANGE IN RESISTANCE
I CA242-6 PARKING BRAKE SWITCH – RELEASE: CHANGE IN RESISTANCE
S CA242-7 SCP -
SS CA242-8 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
SG CA242-9 SIGNAL GROUND: GROUND
SS CA242-10 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I CA242-11 CLUTCH PEDAL POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
SG CA242-12 SIGNAL GROUND: GROUND
General Electronic Control Module
Pin Description and Characteristic
S FH59-1 SCP -
S FH59-7 SCP +
PG FH59-12 POWER GROUND: GROUND
B+ FH60-1 SWITCHED SYSTEM POWER SUPPLY: B+
I FH60-2 VARIABLE ASSIST STEERING ACTUATOR RETURN: VARIABLE VOLTAGE
O FH60-9 VARIABLE ASSIST STEERING ACTUATOR DRIVE: B+ (PWM)
PG FH60-11 POWER GROUND: GROUND
PG FH60-13 POWER GROUND: GROUND
PG FH60-14 POWER GROUND: GROUND
PG FH60-15 POWER GROUND: GROUND
NOTE: Refer to the Appendix at the rear of this book for Network Messages.