Setting the audio delay level— audio delay, Selecting the output video signals— video output – JVC RX-D412BUJ User Manual

Page 36

Setting the digital input (DIGITAL IN)
terminals—DIGITAL IN 1/2/3

When you use the digital input terminals, register what
components are connected to which terminals—DIGITAL
IN 1/2/3 (see page 14) so that the correct source name will
appear when you select the digital source.
Select one of the following components for each terminal:

DVR/DVD

For the DVD player (or DVD recorder)

DBS

For the DBS tuner

VCR

For the VCR

For the TV

Initial setting:

DVR/DVD (for “DIGITAL IN 1”)
DBS (for “DIGITAL IN 2”)
VCR (for “DIGITAL IN 3”)

NOTES

• You cannot assign the same component for different terminals.
The priority order for assignment is as follows:
“DIGITAL IN 1” > “DIGITAL IN 2” > “DIGITAL IN 3”

Ex.: When “DIGITAL IN 1” is set to “DVR/DVD.”

DIGITAL IN 1

DVR/DVD

DBS

VCR

‘

For “DIGITAL IN 2,” “DBS,” “VCR,” and “TV” are selectable.
• In this case, “VCR” is selected.

DIGITAL IN 2

DVR/DVD

DBS

VCR

‘

For “DIGITAL IN 3,” “DBS” and “TV” are selectable.

DIGITAL IN 3

DVR/DVD

DBS

VCR

: Selectable

: Not selectable

• Setting “DIGITAL IN 1” affects “DIGITAL IN 2” and “DIGITAL IN 3”

settings. When you have changed “DIGITAL IN 1,” confirm the
components assigned to “DIGITAL IN 2” and “DIGITAL IN 3.”

Setting the Audio delay level—
AUDIO DELAY

Synchronization between audio and video reproduction can
be possibly disturbed because video signal decoding is time-
consuming compared to the audio signal decoding.
On this setting, you can correct synchronization between
video and audio signals by delaying the audio signal timing.

Adjustable range: OFF and 10 ms to 150 ms (in 10 ms

intervals)

Initial setting:

OFF

NOTE

The audio delay level setting does not take effect when selecting “A
MULTI” for the audio input setting (see page 11).

Selecting the source for HDMI
terminal and COMPONENT VIDEO
jacks—HDMI SELECT/CMPNT SELECT

When you connect a VCR or DBS to the HDMI VCR(DBS) IN
terminal or COMPONENT VIDEO jacks on the rear of the
receiver, you need to select either “VCR” or “DBS” for each
terminal according to the component you connect.
If you have not selected an appropriate source, you cannot
view the playback picture on the TV.

For the HDMI terminal:

HDMI VCR

Select this when connecting a VCR to the
HDMI terminal.

HDMI DBS

Select this when connecting a DBS tuner to
the HDMI terminal.

Initial setting:

VCR

For the COMPONENT VIDEO jacks:

CMPNT VCR

Select this when connecting a VCR to the
COMPONENT VIDEO jacks.

CMPNT DBS

Select this when connecting a DBS tuner to
the COMPONENT VIDEO jacks.

Initial setting:

VCR

Selecting the output video signals—
VIDEO OUTPUT

When you connect your TV and this receiver with the HDMI
cable, set this setting to “HDMI.”
With this setting, this receiver converts incoming composite
video, S-video, and component video signals from video
components and transmits the converted signals through the
HDMI cable.

VIDEO HDMI

Select this when connecting a TV to the
HDMI terminal.

VIDEO OTHER

Select this when connecting a TV to any
video jack other than the HDMI terminal.

Initial setting:

HDMI

NOTE

When selecting “HDMI,” the AV COMPU LINK remote control system is
restricted (see page 45).

29-34_BasicSt.indd 34

06.6.27 2:42:40 PM