JVC TH-A75 - Manual (Page 21)

17
Adjusting the volume
You can adjust the volume level within the range of “0”
(minimum) to “70” (maximum).
Press VOLUME +/–.
• Press + to increase the volume.
• Press – to decrease the volume.
The volume level appears on the display.
CAUTION:
Always set the volume to the minimum before starting any
source.
If the volume is set at its high level, the sudden blast of sound
energy can permanently damage your hearing and/or ruin your
speakers.
7 Listening with headphones
Connect a pair of headphones to the PHONES jack on the
center unit
. This cancels the Surround/DSP mode (see pages
27 to 31) currently selected, deactivates speakers, and
activates the HEADPHONE mode.
• Disconnecting a pair of headphones from the PHONES jack
cancels the HEADPHONE mode and activates speakers
and previously selected Surround/DSP mode.
HEADPHONE mode
When using the headphones, the following signals are
transmitted regardless of your speaker setting:
—For 2 channel sources, the front left and right channel
signals are output directly from the left and right
headphones.
—For multi-channel sources, the front left and right,
center and surround channel signals are down-mixed
and then output from the headphones.
You can enjoy down-mixed multi-channel sound source
using the headphones.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as high volume can
damage both the headphones and your hearing.
• Before removing headphones, as high volume may output from the
speakers.
Adjusting the output level of
subwoofer
You can adjust the output level of the subwoofer.
Once you have adjusted the output level of the subwoofer,
the adjustment is memorized for each source.
You can also adjust the output level using the on-screen
menu (see page 55).
From the remote control ONLY:
1 Press SOUND.
2 Press S.WFR +/– to adjust the output level
of the subwoofer (–10 dB to +10 dB).
Turning off the sound
temporarily
From the remote control ONLY:
Press MUTING.
“MUTING” appears on the display and the volume turns off.
To restore the sound
Press MUTING again.
• Pressing VOLUME +/– also restores the sound.
Adjusting the brightness
You can dim the indications on the display.
From the remote control ONLY:
Press DIMMER.
Each time you press the button, the brightness level
changes as follows.
OFF ] DIMMER 1 ] DIMMER 2 ] (back to the beginning)
DIMMER 1 :Dims the display and the blue light on the
both sides of the display.
DIMMER 2 :Dims the display and turns off the blue
light on the both sides of the display.
OFF :Lights up the display and the blue light
on the both sides of the display.
L
S.WFR
R
CHANNEL/ZOOM VOLUME TV VOL
TUNING
STOP
DIMMER
PAUSE
FF/ /REW
TV/VIDEO
1
MUTING
¡
REC
PLAY
DOWN UP
MEMORY STROBE
AUDIO ANGLE SUBTITLE DECODE
RETURN DIGEST
VFP
TOP MENU MENU
CONTROL EFFECT
S.WFR TEST
SLEEP
TV
VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
FM MODE
1 2 3
4 5 6
7 8 9
10 0 +10
100+
SOUND
SURROUND OFF DSP
CENTER
–
+
–
+
–
+
–
+
SURR-L SURR-R S-BACK
–
+
ADJUST
O.T.
REPLAY
AUDIO/
TV/VCR
CATV/DBS
PROGRESSIVE
Set the remote
control mode
selector to
“AUDIO/TV/VCR.”
EN16-21.TH-A75[A]_f 02.10.11, 2:53 PM 17