JBL CVPD50 - Manual (Page 84)

84
box’s channel controls to be active.
Press the
⁄ / ¤ Navigation Button
q until the name of the base
device appears and then press the
Set Button s.
Figure 95
5. At the next display screen (Fig. 96),
you will select the device whose
Channel Up/Down commands will be
used. Press the
⁄ / ¤ Navigation
Button q until the desired device
name appears to the right of the
device in use. In our example, that is
the cable box. When the desired com-
bination of devices appears, press the
Set Button s.
Figure 96
6. When the Set button is pressed, the
display will change to show you that
the new combination of control com-
mands is being saved to the unit’s
memory, as shown in Figure 97. The
word SAVED will flash four times
and then the remote will return to
normal operation.
Figure 97
7. Once the punch-through is pro-
grammed, the Channel Up/Down
Buttons of the second device named
will be used when those controls
g
are pressed while the master device
is in use.
Returning the Channel Control
Settings to Default Operation
If you wish to remove the Channel Punch-
Through so that the commands for
Channel Up/Down are returned to the
factory default setting, follow the steps
shown above, except that in Steps 4 and
5, select the same device for both the
DEVICE IN USE on the left side of the
bottom line and the PUNCH-THROUGH
device. In the example used, the display
to return the remote to default settings
will appear as shown in Figure 98.
Figure 98
Transport Control Punch-Through
The Play e, Stop M, Fast Forward/
Reverse Lf, Pause M, Record
M and Skip Up/Down Jh
Transport Controls are set at the factory
to operate your DVD player, or the con-
trols of a specific device such as a VCR
or CD player when they are selected.
However, by using the Transport Punch-
Through feature you may program these
controls to transmit the commands for a
different device. For example, you may
wish to operate the transport of a VCR
connected to the VCR input as the
default, rather than the button for the
internal DVD player, as shown in the
following example.
1. Press and hold the Remote Menu
Button b for about three seconds
while the message shown in Figure
54 appears in the remote’s LCD
Information Display
2. Release
the button when the red light under
the Set Button s appears.
2. The remote’s MAIN MENU message
(Figure 55) will appear in the LCD dis-
play and the Set Button s will
remain illuminated in red. Press the
⁄ / ¤ Navigation Button q until
PUNCH-THROUGH appears on the
bottom line of the LCD screen, as
shown in Figure 88. Press the Set
Button s to enter the main punch-
through menu branch.
3. At the next menu screen, press the
⁄ / ¤ Navigation Button q until
TRANSPORT appears on the bottom
line of the LCD screen, as shown in
Figure 99. Press the Set Button s
to begin programming the remote for
transport punch-through.
Figure 99
4. The next display screen (Figure 100)
is where you select the device that
will receive the punch-through com-
mands. In our example, that is the
System button, as that is where we
want the VCR’s transport controls to
be active. Press the
⁄ / ¤ Navigation
Button q until the name of the
base device appears, and then press
the Set Button s.
Figure 100
5. At the next display screen (Figure
101), you will select the device
whose transport commands will be
used. Press the
⁄ / ¤ Navigation
Button q until the desired device
name appears to the right of the
device in use. In our example, that is
the VCR. When the desired combina-
tion of devices appears, press the Set
Button s.
Figure 101
6. When the Set button is pressed, the
display will change to show you that
the new combination of control com-
mands is being saved to the unit’s
memory, as shown in Figure 102. The
word SAVED will flash four times
and then the remote will return to
normal operation.
Figure 102
7. Once the punch-through is pro-
grammed, the transport buttons of
the second device named will be
used when those buttons are pressed
while the master device is in use.
Returning the Transport Control
Settings to Default Operation
If you wish to remove the Transport
Punch-Through so that the transport com-
mands are returned to the factory default
setting, follow the steps shown above,
except that in Steps 4 and 5, select the
same device for both the DEVICE IN
USE on the left side of the bottom line
and the PUNCH-THROUGH device. In
the example used, the display to return
the remote to default settings will appear
as shown in Figure 103.
Figure 103
EzSet Configuration
JBL’s patented EzSet feature makes it easier
than ever to calibrate the output levels on
your new home theater system for maxi-
mum playback accuracy. In addition to
automatically setting the levels, the
remote’s LCD display allows the unit to
be used as a direct readout SPL meter.
Complete instructions for using the EzSet
features of the remote are found on page
51 of this owner’s manual.
In most cases, you will find it easier to
access the EzSet capabilities directly by
pressing the SPL Select Button
9
and following the menu prompts as
detailed on page 51. However, there is
one function of the remote that is avail-
P U N C H - T H R O U G H
S Y S
< - S Y S
S Y S < - M / D V D [ T R S ]
S A V E D
P U N C H - T H R O U G H
S Y S
< - M / D V D
D E V I C E I N U S E
M / D V D
P U N C H - T H R O U G H
T R A N S P O R T
P U N C H - T H R O U G H
V C R
< - V C R
V C R < - C B L [ C H A N ]
S A V E D
P U N C H - T H R O U G H
V C R
< - M / D V D
D E V I C E I N U S E
M / D V D
CVR700 OM 12/17/04 4:24 PM Page 84