JBL CVPD50 - Manual (Page 7)

7
SAFETY INFORMATION
Verify Line Voltage Before Use
Your CVR700 and CVPD50 have been
designed for use with 120-volt AC cur-
rent, and the plugs are specifically
designed for 120-volt applications.
Connection to a line voltage other than
that for which the unit is intended can
create a safety and fire hazard and may
damage the unit.
If you have any questions about the volt-
age requirements for your specific model,
or about the line voltage in your area,
contact your selling dealer before plug-
ging the unit into a wall outlet.
Do Not Use Extension Cords
We do not recommend that extension
cords be used with this product. As with
all electrical devices, do not run power
cords under rugs or carpets or place
heavy objects on them. Damaged power
cords should be replaced immediately by
an authorized service center with cords
meeting factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from
an AC outlet, always pull the plug; never
pull the cord. If you do not intend to use
the unit for any considerable length of
time, disconnect the plug from the AC
outlet.
Do Not Open the Cabinet
There are no user-serviceable compo-
nents inside this product. Opening the
cabinet may present a shock hazard, and
any modification to the product will void
your guarantee. If water or any metal
object such as a paper clip, wire or a
staple accidentally falls inside the unit,
disconnect it from the AC power source
immediately, and consult an authorized
service center.
Installation Location
■ To ensure proper operation, and to
avoid the potential for safety hazards,
place the unit on a firm and level sur-
face. When placing the unit on a shelf,
be certain that the shelf and any
mounting hardware can support the
weight of the product.
■ Make certain that proper space is pro-
vided both above and below the unit
for ventilation. If this product will be
installed in a cabinet or other
enclosed area, make certain that there
is sufficient air movement within the
cabinet.
■ Do not place the unit directly on a
carpeted surface.
■ Avoid moist or humid locations.
■ Avoid installation in extremely hot or
cold locations, or an area that is
exposed to direct sunlight or heating
equipment.
■ Do not obstruct the ventilation slots
on the sides of the unit, or place
objects directly over them.
Cleaning
When the unit gets dirty, wipe it with a
clean, soft, dry cloth. If necessary, wipe
it with a soft cloth dampened with mild
soapy water, then a fresh cloth with
clean water. Wipe immediately with a
dry cloth. NEVER use benzene, aerosol
cleaners, thinner, alcohol or any volatile
cleaning agent. Do not use abrasive
cleaners, as they may damage the finish
of metal parts. Avoid spraying insecticide
near the unit.
Unpacking
Cartons and shipping materials used to
protect your new system components
during shipment are specially designed to
cushion them from shock and vibration.
We suggest that you save the carton and
packing materials for use in shipping if
you move, or should the unit ever need
repair.
To minimize the size of the cartons in
storage, you may wish to flatten them.
This is done by carefully slitting the tape
seams on the bottom, and collapsing the
carton down to a more two-dimensional
appearance. Other cardboard inserts may
be stored in the same manner. Packing
materials that cannot be collapsed should
be saved along with the carton in a
plastic bag.
If you do not wish to save the packaging
materials, please note that the carton
and other sections of the shipping protec-
tion are recyclable. Please respect the
environment and discard those materials
at a local recycling center.
Important Note for CVPD50 Plasma
Display: Always make sure that two
people lift the CVPD50 plasma display
together. Never attempt to lift the unit by
yourself. Failure to follow this instruc-
tion may result in personal injury or
irreparable damage to the unit that is
not covered under warranty.
Remove Front-Panel Protective Film
In order to protect the lens covering the
front panel of your new CVR700, it is
shipped from the factory covered by a
protective plastic film. Before using the
unit, remove this film by grabbing one
corner and gently peeling back the plastic
sheet. Note that the film must be
removed for proper operation of the
remote control.
CVR700 OM 12/17/04 4:23 PM Page 7