JBL Custom Shop CSC2295H - Manual

CSC2295H
12” Two-Way System
Horizontal Configuration
90
O x 90 O Coverage Pattern
For Permanent Installation
Key Features:
4
2206H 12” VGC (Vented Gap
Cooled
TM LF transducer
4
2332 Optimized Aperture TM HF
horn with 1.5” throat
4
2447J 4” diaphragm, 1.5” throat
compression driver
4
Compact trapezoidal enclosure
4
DuraFlex finish - tough, weather
resistant and paintable
4
Tamper resistant internal Bi-
amp/Passive crossover selector
4
Advanced Network Topology for
smooth power response and sta-
ble amplifier loading
4
Versatile complement of suspen-
sion points
The CSC2295H is a JBL Custom
Shop produced adaptation of the
Sound Power series SP212-9. The
same transducers and switchable
passive/active crossover network
have been repackaged in a horizon-
tal configuration enclosure. All of the
features of the standard product
have been maintained while adding
installation flexibility.
The CSC2295H is available on a
build-to-order basis. Contact the
Custom Shop for information on
availability and lead time.
1 Rating based on test signal of IEC filtered random noise
with a peak-to-average ratio of 6 dB, two hours duration.
2 Sensitivity is based on a swept 500 Hz to 2.5 kHz test sig-
nal for an input of 2.83V @ 8 ohms.
JBL continually engages in research related to product
improvement. Some materials, production methods and
design refinements are introduced into existing products
without notice as a routine expression of that philosophy.
For this reason, any current JBL product may differ in some
respect from its published description, but will always equal
or exceed the original design specifications unless other-
wise stated.
2/28/01 ATR
Preliminary Specifications:
System:
Frequency Range (-10 dB): 37 Hz - 20 kHz
Frequency Response (±3 dB): 60 Hz - 18 kHz
Horizontal Coverage Angle (-6 dB): 95° averaged 500 Hz to 16 kHz
Vertical Coverage Angle (-6 dB): 70° averaged 500 Hz to 16 kHz
Directivity Factor (Q): 9.0 averaged 500 Hz to 16 kHz
Directivity Index (DI): 9.0 dB averaged 500 Hz to 16 kHz
Sensitivity 2 : 95 dB SPL, 1W @ 1m (3.3 ft)
Calculated Maximum SPL 2 : 129 dB SPL, 1W @ 1m (3.3 ft)
Nominal Impedance: 8 ohms (Passive crossover mode)
Power Rating 1 : 600 watts IEC, 2400 watts peak
Recommended Amplifier Power: 800 watts
Recommended Controller: DSC260
Transducers:
Low Frequency: 2206H, 300 mm (12 in) dia., 100 mm (4 in) edge
wound ribbon voice coil
Nominal Impedance: 8 Ohms
Power Rating: 600 watts AES, 2400 watts peak
Sensitivity 2 : 95 dB SPL, 1W @ 1m (3.3 ft)
Calculated Maximum SPL 2 : 129 dB SPL, 1W @ 1m (3.3 ft)
Recommended Amplifier Power: 800 watts
High Frequency: 2447J; 100 mm (4”) diaphragm and voicecoil
dia., 76 mm (1.5”) throat dia.; 2332 horn
Nominal Impedance: 16 Ohms
Input Power Rating: 75 W AES; 300 W Peak
Sensitivity 2 : 111 dB, 1 W @ 1 m (3.3’)
Calculated Maximum SPL: 136 dB @ 1 m (3.3’)
Recommended Amplifier: 200 W
Physical:
Enclosure: Trapezoidal, 15 o top & bottom angles, 18 mm
birch plywood
Environmental Specifications: Mil-Std 810, IPX4 per IEC 529
Suspension Attachment: 12 points, accept M10 threaded hardware
Finish: Black DuraFlex coating
(white or custom color optional)
Grille: Black powder coated 18 gauge
perforated steel grille with foam backing (white or
custom color optional)
Input Connector: 2 x NL4 Neutrik Speakon connector
Dimensions (H x W x D): 394 mm x 711 mm x 378 mm
(15.5 in x 28 in x 14.88 in)
Net Weight: 31.8 kg (70 lb)
Custom Shop
Rear
Top/Bottom
Front
28
15.5
Sides
14.88
30°