Motion detection settings – MITSUBISHI ELECTRIC DX-NT400E User Manual
Page 38
38
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
1. In “SELECTION CAMERA NUMBER,” select the camera
for which the detection area is set.
2. Select “DETECTION MASK SETTING” and press the
ENTER button.
• The dotted screen with detection areas is displayed and
the background of the most upper left dot turns red and
flashes.
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
3. Use the JOG , , , buttons to select the dot to activate/
inactivate and press the ENTER button.
• The “
&
&
&
&
&
” (active) setting changes to “ • ” (inactive) setting.
• & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
& & & & & & & & & & & & & & & &
When pressing the + button, all the dots change
to “
&
” (active). When pressing the – button, all the
dots change to “ • ” (inactive).
4. Repeat step 3 to activate/inactivate all the desired dots.
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
• • • • • • • • & & & & & & & &
5. Press the CLEAR button.
• The setting is determined and the display returns to the
While setting the detection mask, other settings
are not accepted. To exit the menu screen during
setting, press the CLEAR button.
This menu is used to set the conditions of the motion
detection function for alarm recording which is started when
detecting motion within the video of the connected camera.
■
SELECTION CAMERA NUMBER
This item is used to set the camera number for which motion
detection function is executed. Since settings can be made
for each camera individually, more detailed settings are
possible.
1
>>SELECTION CAMERA NUMBER
DETECTION MASK SETTING
SENSITIVITY HIGH••<<
TEST MODE
MD LOCK OUT TIME OFF
Setting (default: “
1
”)
“
1
,” “
2
,” “
3
,” “
4
”
When selecting the SETTINGS> screen during single screen display of 1. Press the SET UP button } } Select “SELECTION CAMERA NUMBER” in the 2. When “SELECTION CAMERA NUMBER” setting is 3. Press the CLEAR button or the SET UP button. The motion detection function does not operate while the ■ DETECTION MASK SETTING This item is used to set the area to activate motion detection. Definition of setting mark (default: all areas “ & ” (active)) “ & ”: Area activated with motion detection. “ • ”: Area inactivated with motion detection. It is possible to set multiple areas for one camera. Example of screen setting & ” for the right half of the screen to activate motion detection.
any specified camera number, that camera number
is displayed as the initial setting of “SELECTION
CAMERA NUMBER.”
and determine such setting.
determined, the background screen is switched to the video
of the selected camera number.
screen is displayed.
Any of the 192 dotted detection areas which are equally
splited to 16 X 12 pixel sizes of the individually loaded video
of each connected camera can be selected.
For the video loaded from the camera number set in “SE-
LECTION CAMERA NUMBER”:
• Displaying “
• Displaying “ • ” for the left half of the screen to inactivate
motion detection.