177 data type – Fostex D-160 User Manual
Page 177

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)
177
Data Type
< l o o p o p . m o d e >
< l o o p o p . m o d e >
< l o o p o p . m o d e >
< l o o p o p . m o d e >
< l o o p o p . m o d e >
12=stop
Indicates the next operating mode following locating to the start point (GP1) upon
arriving at the end point (GP6) by the play mode.
In D-160, 12=stop only is effective.
< p o s t l o c a t e m o d e >
< p o s t l o c a t e m o d e >
< p o s t l o c a t e m o d e >
< p o s t l o c a t e m o d e >
< p o s t l o c a t e m o d e >
12=stop
15=play
Specifies operating mode in which D-160 should enter upon completing the
locate operation. Corresponds to the setting of AUTO PLAY ON ("15")/OFF ("12") on
the main unit.
< c o u n t >
< c o u n t >
< c o u n t >
< c o u n t >
< c o u n t >
01~7F
Specifies succeeding data byte numbers.
< m m c t r a c k >
< m m c t r a c k >
< m m c t r a c k >
< m m c t r a c k >
< m m c t r a c k >
Complies to the MMC (MIDI MACHINE CONTROL) standard track bit map.
In D-160, you always need to specify three byte combinations of "r0", "r1" and "r2."
< e d i t m e s s a g e >
< e d i t m e s s a g e >
< e d i t m e s s a g e >
< e d i t m e s s a g e >
< e d i t m e s s a g e >
00 = no message
01 = completed (completion flag)
02 = active (execution flag)
02
02
03 = cancel (execution stop)
05 = Indicates rehearsal (rehearsal mode of auto rec). Possible of undo.
06 = Indicates take (take mode of auto rec). Possible of undo.
10 = over value error
10
capacity shortage) and
time required for a minimum one time paste.
11 = Indicates in point error (incorrect in point).
12 = Indicates out point error (incorrect out point).
14 = Indicates void data (data necessary for paste does not exist).
18 = Indicates track select error (track necessary to execute copy/move or erase/cut
is not correctly setup).
19
by
1A = Indicates disable rec (record disable mode).
71 = Indicates on.
72 = Indicates off.
< m m c t i m e >
< m m c t i m e >
< m m c t i m e >
< m m c t i m e >
< m m c t i m e >
hr mn sc fr {ff/st} complies to the MMC standard time code.
< o n / o f f >
< o n / o f f >
< o n / o f f >
< o n / o f f >
< o n / o f f >
70 = default
71 = on
72 = off
< r e p e a t c o u n t >
< r e p e a t c o u n t >
< r e p e a t c o u n t >
< r e p e a t c o u n t >
< r e p e a t c o u n t >
01~7F
Especially when executing commands such as paste, the number of pasting times to
be continuously repeated following the auto punch in point is specified.
< c h a n n e l >
< c h a n n e l >
< c h a n n e l >
< c h a n n e l >
< c h a n n e l >
1~18, 7F
Select recorder tracks 1~18. "00" in particular, is not specified (default setting). "7F"
indicates input/output of Adat optical. For details, refer to explanation on setting
the Command/Mode.
< l o c k e n a b l e >
< l o c k e n a b l e >
< l o c k e n a b l e >
< l o c k e n a b l e >
< l o c k e n a b l e >
00 = lock disable, chase disable
01 = lock enable, chase enable
Corresponds to SLAVE ON ("01")/OFF ("00") in the main unit.
< l o c k s t a t u s >
< l o c k s t a t u s >
< l o c k s t a t u s >
< l o c k s t a t u s >
< l o c k s t a t u s >
00 = lock disable, chase disable
01 = lock enable (unlocked), chase enable (unlocked)
11 = lock enable (locked), chase enable (locked)
< p r o g r a m >
< p r o g r a m >
< p r o g r a m >
< p r o g r a m >
< p r o g r a m >
01~63H
Indicates program numbers (P1~P99) on the main unit. However, D-160 can specify
only 01 (corresponds to P1)~63H (corresponds to P99).
< l o c k m o d e >
< l o c k m o d e >
< l o c k m o d e >
< l o c k m o d e >
< l o c k m o d e >
40 = Free
42 = Vari
45 = SP DIF
46 = adat
Indicates the slave mode when this equipment is set to slave ON.