Sony ECM-X7BMP Electret Condenser Lavalier Microphone for UWP Transmitters - Manual (Page 35)

Adjustment Using the Menus
35
[Copy From]
Copies the other color temperature.
Note
Use the BKM-16R with software version 1.6 or higher or
BKM-17R to use the [Copy From] function.
[Original Value] Sets the initial value.
Except for the XYZ format signal
You can select from [D93], [D65],
[D61], [D55], [DCI], [User1], [User2],
[User3], [User4], or [User5].
When [D93], [D65], [D61], [D55], or
[DCI] data is changed, they are
displayed as [D93*], [D65*], [D61*],
[D55*], or [DCI*].
For the XYZ format signal
You can select from [DCI XYZ], [User
XYZ1], [User XYZ2], [User XYZ3],
[User XYZ4], or [User XYZ5].
When the [DCI XYZ] data is changed,
it is displayed as [DCI XYZ*].
[Signal] Sets the white signal to be used for
adjustment.
 [Internal]: Select when an internal
signal is used. The signal is
automatically switched in
synchronization with the gain and
bias adjustments.
 [External]: Select when an external
input signal is used. Supply a signal
to be used when adjusting gain and
bias.
Note
If [Internal] is selected for the XYZ
format signal, the Calibration White
signal is displayed.
[Contrast/Bright
Hold] Sets the contrast and brightness to the
adjusted value or center value.
 [Off]: Sets contrast and brightness
to the center values during and after
color temperature adjustment.
 [On]: Retains the adjusted contrast
and brightness values during and
after color temperature adjustment.
Submenu Setting
Submenu Setting
[Preset Value] Copies other data in this monitor.
Except for the XYZ format signal
When the item is selected, you can
select from the following:
 [D93]: Copies the color temperature
of D93.
 [D65]: Copies the color temperature
of D65.
 [D61]: Copies the color temperature
of D61.
 [D55]: Copies the color temperature
of D55.
 [DCI]: Copies the color temperature
of DCI.
 [User1] to [User5]: Copies the color
temperature of User1 to User5.
When [D93], [D65], [D61], [D55], or
[DCI] data is changed, they are
displayed as [D93*], [D65*], [D61*],
[D55*], or [DCI*].
For the XYZ format signal
When the item is selected, you can
select from the following:
 [DCI XYZ]: Copies the color
temperature of DCI XYZ.
 [User XYZ1] to [User XYZ5]:
Copies the color temperature of User
XYZ1 to User XYZ5.
When [DCI XYZ] data is changed, it is
displayed as [DCI XYZ*].
[Other Monitor] Copies data from another monitor.
Note
Use the BVM-E251/BVM-E171 as a
source monitor to use the [Other
Monitor] function.
[Monitor ID] Enter the ID number of the source
monitor.
When the NETWORK switch is set to
PEER TO PEER, this is not selectable.
Except for the XYZ format signal
When the ID number is entered, you
can select from the following:
 [D93]: Copies the color temperature
of D93.
 [D65]: Copies the color temperature
of D65.
 [D61]: Copies the color temperature
of D61.
 [D55]: Copies the color temperature
of D55.
 [DCI]: Copies the color temperature
of DCI.
 [User1] to [User5]: Copies the color
temperature of User1 to User5.
When [D93], [D65], [D61], [D55], or
[DCI] data is changed, they are
displayed as [D93*], [D65*], [D61*],
[D55*], or [DCI*].