KEPCO HSP Series Operator Manual - Manual (Page 3)

HSP OPR 050614
i/(ii Blank)
TABLE OF CONTENTS
SECTION PAGE
SECTION 1 - INTRODUCTION
1.1 Scope of Manual ..................................................................................................................................... 1-1
1.2 General Description................................................................................................................................. 1-1
1.3 Specifications .......................................................................................................................................... 1-1
1.4 Miscellaneous Features .......................................................................................................................... 1-5
1.4.1 Control/Programming......................................................................................................................... 1-5
1.4.2 Status Indicators/Flags ...................................................................................................................... 1-5
1.4.3 Setpoint Monitors:.............................................................................................................................. 1-5
1.4.4 Remote Error Sensing: ...................................................................................................................... 1-5
1.4.5 Load Sharing: .................................................................................................................................... 1-5
1.4.6 Load Monitor:..................................................................................................................................... 1-6
1.4.7 Auxiliary Supply: ................................................................................................................................ 1-6
1.4.8 Overcurrent/Undervoltage Protection: ............................................................................................... 1-6
1.4.9 Current Walk-in:................................................................................................................................. 1-6
1.4.10 Remote Reset:................................................................................................................................... 1-6
1.5 Options .................................................................................................................................................... 1-6
1.5.1 Meters (M Suffix): .............................................................................................................................. 1-6
1.5.2 Battery Chargers (B Suffix):............................................................................................................... 1-6
1.5.3 Internal Blocking Diode (R Suffix):..................................................................................................... 1-6
1.6 Accessories ............................................................................................................................................. 1-6
SECTION 2 - INSTALLATION
2.1 Unpacking and Inspection ....................................................................................................................... 2-1
2.2 Terminations and Controls ...................................................................................................................... 2-1
2.3 Source Power Requirements .................................................................................................................. 2-3
2.4 Cooling .................................................................................................................................................... 2-3
2.5 Preliminary Operational Check................................................................................................................ 2-3
2.6 Installation ............................................................................................................................................... 2-4
2.7 Wiring Instructions ................................................................................................................................... 2-4
2.7.1 Safety Grounding............................................................................................................................... 2-4
2.7.2 Source Power Connections ............................................................................................................... 2-5
2.7.3 D-C Output Grounding....................................................................................................................... 2-5
2.7.4 Power Supply/Load Interface............................................................................................................. 2-6
2.7.5 Load Connection - General................................................................................................................ 2-6
2.7.5.1 Load Connection - Method I (Local Error Sensing)...................................................................... 2-7
2.7.5.2 Load Connection - Method II (Remote Error Sensing)................................................................. 2-8
2.7.5.3 Load Connection - Method III (Series Connection)...................................................................... 2-9
2.7.5.4 Load Connection - Method IV (Parallel Operation) ...................................................................... 2-10
2.7.5.4.1 Redundancy and Hot Swap Applications ................................................................................2-10
2.7.6 Load Sharing ..................................................................................................................................... 2-11
2.7.7 Signal Connections............................................................................................................................ 2-12
2.8 Mechanical Keying .................................................................................................................................. 2-12
2.9 Retaining Latches.................................................................................................................................... 2-12
SECTION 3 - OPERATING INSTRUCTIONS
3.1 Operating Configuration .......................................................................................................................... 3-1
3.2 Remote Error Sense................................................................................................................................ 3-1
3.3 Output Voltage Programming .................................................................................................................. 3-1
3.4 Output Voltage Range ............................................................................................................................. 3-2
3.5 Current Limit Programming ..................................................................................................................... 3-2
3.6 Current Limit Programming Range.......................................................................................................... 3-3
3.7 Setpoint Monitors .................................................................................................................................... 3-3
3.8 Overvoltage Protection Adjustment ......................................................................................................... 3-4
3.9 Current Limit Characteristic ..................................................................................................................... 3-5
3.10 Current Walk-in Circuit ............................................................................................................................ 3-6
3.11 5VAUX Floating Supply ........................................................................................................................... 3-6
3.12 Remote Inhibit/Remote Reset Controls ................................................................................................... 3-7