0 transmitters, see table 2-4, See table 2-5 fo – Emerson Network Router User Manual
Page 26
20
ProLink
®
II Software for Micro Motion
®
Transmitters
Installation and Setup
Table 2-4
Default communication parameters for Series 1000/2000/3000 transmitters
Default values
Transmitter
Physical layer
Protocol
Baud
Data
bits
(1)
(1) ProLink II automatically sets data bits appropriately for the configured protocol. Even though a data bits parameter may be
configured in the transmitter, you do not need to configure it in ProLink II. HART protocol is always 8 data bits. If your transmitter
is configured for Modbus with 7 data bits, specify Modbus ASCII; if your transmitter is configured for Modbus with 8 data bits, specify
Modbus RTU.
Stop
bits
Parity
Address
Model 1500/2500
Bell 202
(2)(3)
(2) Connection to primary mA output, or to HART clips (Model 2400S and Model 2200S transmitters only).
(3) Except Model 1500 transmitter with the Filling and Dosing application. The Model 1500 transmitter with the Filling and Dosing
application does not support Bell 202 / HART communication.
HART
(4)
(4) HART/Bell 202 parameters are not configurable. The settings shown here are always in effect.
1200
8
1
odd
0
RS-485
(5)
(5) Connection to RS-485 terminals.
Modbus RTU
9600
8
1
odd
1
Model 1700/2700
Analog
Bell 202
HART
1200
8
1
odd
0
RS-485
(6) Available only on Model 1700/2700 transmitters with analog outputs.
HART
1200
8
1
odd
0
Model 1700/2700 I.S.,
Model 2700 Config. I/O
Bell 202
HART
1200
8
1
odd
0
Model 2200S
Bell 202
HART
1200
8
1
odd
0
Model 2400S Analog
Bell 202
HART
1200
8
1
odd
0
RS-485
Modbus
(RTU or ASCII)
Auto-
detect
Auto-
detect
Auto-
detect
Auto-
detect
1
Series 3000
Bell 202
HART
1200
8
1
odd
0
RS-485
Modbus RTU
9600
8
1
odd
1
Table 2-5
Default communication parameters for LF-Series transmitters
Default values
Transmitter
Physical layer
Protocol
Baud
Data
bits
(1)
(1) ProLink II automatically sets data bits appropriately for the configured protocol. Even though a data bits parameter may be
configured in the transmitter, you do not need to configure it in ProLink II. HART protocol is always 8 data bits. If your transmitter
is configured for Modbus with 7 data bits, specify Modbus ASCII; if your transmitter is configured for Modbus with 8 data bits, specify
Modbus RTU.
Stop
bits
Parity
Address
DIN rail
Bell 202
(2)(3)
(2) Connection to primary mA output.
(3) Except transmitters with the Filling and Dosing application. Transmitters with the Filling and Dosing application do not support
Bell 202 / HART communication.
HART
(4)
(4) HART/Bell 202 parameters are not configurable. The settings shown here are always in effect.
1200
8
1
odd
0
RS-485
(5)
(5) Connection to RS-485 terminals.
Modbus RTU
9600
8
1
odd
1
Field-mount with output
option 1 or 3
Bell 202
HART
1200
8
1
odd
0
RS-485
HART
1200
8
1
odd
0
Field-mount with output
option 4
Bell 202
HART
1200
8
1
odd
0