HEIDENHAIN TNC 122 User Manual - Manual (Page 61)

Subject Index
TNC 122 61
A
Accessory ........................ 4, 60
Actual value, entering the ..... 21
Angle step ........................... 40
Approaching the workpiece . 51
Automatic program run ........ 52
B
Block, current ...................... 33
Bolt hole circle ..................... 27
C
CALL LBL ............................ 43
Chain dimensions ................ 13
Circle segment .................... 40
Coordinate axes ................... 11
Coordinate system ....... 11, 12
Coordinates
Absolute ....................... 13
Geographic ................... 11
Incremental .................. 13
Correcting entries ................ 33
CYCL ................................... 39
D
Data interface ...................... 60
Datum
Absolute ....................... 12
Relative ........................ 12
setting .................... 12, 21
Display step ......................... 60
E
Error messages ................... 16
F
Feed rate F .......................... 60
in the program .............. 35
Maximum permissible .. 60
Floppy disk unit ............... 4, 60
Flowcharts, Dialog ................. 6
G
Guideline for programming .... 2
H
Hole pattern ......................... 27
I
Incremental coordinates ...... 13
Input range .......................... 60
K
Keys for operating modes ... 16
L
Labels .................................. 43
LBL ...................................... 43
Linear hole pattern .............. 27
M
Machine axes ...................... 11
Moving the ................... 19
Manual operation ................. 19
Manual, scope of ................... 5
Measurement, units of ........ 60
Memory capacity ................. 60
Milling a shoulder ................ 25
Miscellaneous functions ...... 55
Mode of operation ............... 16
Switching the ............... 16
N
Nesting, maximum depth .... 43
Nominal position
in the program .............. 31
O
Overviews ........................... 55
P
Position data
Fundamentals of ........... 11
Position display mode
Selecting the ................ 17
Position feedback ................ 14
POSITIONING WITH MDI .... 23
Bolt hole circles ............ 27
Positions
Capturing actual ............ 38
Entering ........................ 25
Moving to ..................... 25
Power consumption ............ 60
Pre-positioning ..................... 31
for program run ............ 51
Program
archiving ....................... 49
blocks ........................... 33
deleting ........................ 32
editing ................... 16, 31
execution ............... 16, 51
interruption ................... 36
management ................ 32
markers ........................ 43
number ......................... 32
transfer ......................... 50
Program run
Automatic ..................... 51
Preparation for .............. 51
Prepositioning the tool . 51
Single block .................. 51
Stop .............................. 55
Workpiece approach for 51
Program section
deletion ........................ 34
repeats ......................... 46
Programming steps ............. 37
Prompt ................................... 6
R
Range of traverse ................ 60
Reference marks ................. 14
Crossing over ............... 15
Distance-coded ............. 14
Reference point ................... 14
Reference system ............... 11
S
Setup ................................... 19
Shoulder milling ................... 25
Software version ................... 5
Specifications ...................... 60
Spindle
ON ................................ 55
STOP ............................ 55
Starting angle ...................... 27
Stop block ............................ 36
Stop program run ................ 55
Subprogramming ................. 44
Switch-on ............................ 15
T
Tables .................................. 55
Teach-in ............................... 38
Temperature, ambient ......... 60
Tool length ........................... 20
Tool movement ............ 14, 31
Tool radius ..................... 20, 23
compensation ............... 23
Tools ............................. 20, 23
Traverse ............................... 19
with axis buttons ........... 19
Traverse range ..................... 60
U
User parameters .................. 53
W
Weight ................................. 60
Workpiece
Approaching the ........... 51
Workpiece movement ......... 31
Workpiece positions ............ 13
Absolute ....................... 13
in the program .............. 31
Incremental .................. 13
Z
Zero tool .............................. 20