Double check your work, Reconnect the negative battery cable – Airaid 510-312 User Manual
Page 4
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
39. Install the Airaid Intake Tube onto the Cold Air Box
and the throttle body, align and tighten all four of the
Clamps. Reconnect the Mass Air Flow sensor. Connect
the factory crank case breather line to the 3/8 Barbed
Elbow on the Intake Tube
36. Transfer the Mass Air Flow sensor from the factory
airbox, into the Airaid Intake tube and secure using the
two #8 Spacers (#21) and 8-32 Socket Head screws
(#22) . Do not use the factory screws.
37. Install the 1/8”and 3/8” barbed fittings (#s 13 and 14)
into the Airaid Intake Tube as shown.
38. Slide the Hump Hose (#7), and two #68 Hose
Clamps (#25), onto the Intake Tube as shown. Slide the
Reducing Coupler (#8) and the #48 (#23) and #64
Clamps (#24) on the other end of the Intake Tube. Leave
the Clamps loose for now.
43.
Double check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses,
bolts, and screws are tight. Double check the
hood clearance!
Reconnect the negative battery cable!
REV.12.08.14
41. Install the Airaid Premium Filter onto the Filter
Adapter inside of the airbox and tighten the clamp.
42. Place the Gasket (#10) onto the underside of the Air
Box Lid (#4) and peel off the protective film. Mount the
lid on the Air Box using four 1/4-20 x 1/2” Button Head
Bolts (#18), and 1/4” Flat washers (#19).
Reducer
35. Mount the Cold Air Box onto the CAB Mounts using
the three 8mm Bolts (#14) and 5/16 Flat Washers (#16).
Verify that sufficient clearance for the reconfigured
AC lines has been made.
40. replace the OEM vacuum line on the fuel pressure
regulator with the supplied 20 1/2” 1/8” line (#12). Con-
nect the 1/8” line to the small Fitting on the Intake tube.
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
SPACER
Hump Hose
Reducer
Pre Filter Option- Part Number 799-445
For maximum protection in the harshest of environments
Airaid offers a slip on Pre Filter.
- Prolongs Cleaning Intervals
- Water Repellant
- Free Flowing Protection
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-
ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-462 Airaid Oiled Media 701-462 Airaid SynthaMax Dry Media - Red
702-462 Airaid SynthaMax dry Media - Black 703-462 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!
Synthamax Air Filters do not require oil. Ser-
vice air filter as needed by cleaning with com-
mon non-petroleum all-purpose household
cleaner and water. Simple Green®, Formula
409® or equivalent works great. Apply cleaner
to outside of air filter and allow to soak. Then
flush filter clean from the inside out with a gar-
den hose and repeat steps if necessary. Do not
apply high pressure water or air to clean filter.
Allow filter to air dry and reinstall
.