beautypg.com

Airaid 200-197 User Manual

Installation instructions, Component identification

background image

Installation Instructions

For Part Numbers:

200-197

700-469 Airaid Oiled Media Filter

201-197

701-469 SynthaMax Dry Media Filter - Red

202-197

702-469 SynthaMax Dry Media Filter - Black

203-197

703-469 SynthaMax Dry Media Filter - Blue


2007-08 Cadillac Escalade/ESV/EXT
2007-08 Chevrolet Avalanche
2007-08 Chevrolet Silverado 1500/2500HD/3500HD
2007-08 Chevrolet Tahoe/Suburban 1500/2500
2007-08 GMC Sierra 1500/2500HD/3500HD
2007-08 GMC Yukon/Yukon XL 1500/2500
2007-08 GMC Denali/Denali XL
4.3L V6, 4.8L V8, 5.3L V8, 6.0L V8, 6.2L V8
(GMT-900 Body Style Only)

Component Identification

1.

Airaid Premium Filter

1

2. MAF Panel

1

3. Rear Air Dam Panel

1

4. Airaid Intake Tube

1

5. Air Filter Adapter

1

6. Urethane Hump Hose

1

7. Urethane Coupler

1

8. 3/8” x 14” Breather Hose

1

9. Weather Strip 20 3/4”

1

10.

6-32 x 5/16” Screw

5

11.

#6 Flat Washer

5

12.

6-32 Keps Nut

5

13.

1/4 - 20 x 1/2” Button Head Bolt 3

14.

1/4” Flat Washer

7

15.

M6 - 1 x 25 Hex Bolt

4

16.

#64 Hose Clamp

4

17.

1/4” NPT x 3/8” Barb Fitting

1

1. Disconnect the negative battery cable.
Remove the factory beauty cover by lifting up on
the front, and then pulling the cover towards the
front of the vehicle. It is only held in place by
grommets.

2. Disconnect the factory breather hose at the
valve cover.

3. Separate the factory intake tube from the plas-
tic clamp that secures the radiator hose to the
tube. A firm downward push will usually do it.

4. Loosen three hose clamps. One at each end of
the factory intake tube, and one on the Mass Air
Flow sensor (MAF) wher e it clamps to the fac-
tory airbox.

5. Slide the factory intake tube off of the MAF
sensor, rotate it up so that it disengages from the
mounting grommet on the intake manifold, and
then slide it forward off of the throttle body and
remove it from the vehicle.

6. Remove, and set aside the MAF sensor from
the factory airbox using caution to retain the fac-
tory clamp and seal.

7. Rock the factory airbox back and forth to loos-
en it from the mounting grommets, and remove it
from the vehicle.

8.Using a 10mm socket, remove four bolts, and
then remove the factory airbox mounting plate
from the vehicle.

9. Assemble the Cool Air Dam panels (CAD) (#2
& #3) using five 6-32 x 5/16” screws (#10), #6
flat washers (#11), and 6-32 keps nuts (#12). Next
install the air filter adapter (#5) into the panels as
shown using three 1/4 - 20 x 1/2” button head
bolts (#13), and 1/4” flat washers (#14).

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

This manual is related to the following products: