Airaid 200-247 - Manual

Component Identification
1. Airaid Premium Filter 1
2. Airaid Intake Tube 1
3. Cool Air Box 1
4. Air Filter Adapter 1
5. Urethane Hump Hose 1
6. Coupler W/ #68 Clamp 1
7. Weather Strip 25” 1
8. ¼-20 x ½” Button Head Bolt 3
9. 1/4-20x 3/4” Hex Bolt 1
10. 1/4” Nylock Nut 1
11. ¼” Flat Washer 8
12. M6-1x25 Hex Bolt 3
13. #60 Hose Clamp 2
14. Bracket 1
Installation Instructions
For Part Numbers:
200-247 720-472 Airaid Oiled Media Filter
201-247 721-472 SynthaMax Dry Media Filter - Red
202-247 722-472 SynthaMax Dry Media Filter - Black
203-247 723-472 SynthaMax Dry Media Filter - Blue
2002-04 Cadillac Escalade
2002-04 Chevrolet Avalanche 1500
1999-04 Chevrolet Silverado 1500
2001-03 Chevrolet Silverado 1500HD
1999-04 Chevrolet Silverado 2500HD/3500HD
2000-04 Chevrolet Tahoe/Suburban 1500
2000-06 Chevrolet Suburban 2500
1999-06 GMC Sierra 1500
2001-06 GMC Sierra 1500HD/2500HD/3500HD
1999-04 GMC Sierra 2500
2007 GMC Sierra Classic 1500/1500HD/2500HD/3500HD
2000-04 GMC Yukon/Yukon XL 1500
2000-03 GMC Yukon XL 2500
4.8L V8, 5.3L V8, 6.0L V8
With Mechanical Cooling Fan and Low Profile Hood
1. Disconnect the negative battery cable.
Loosen the bolt that secures the beauty cover to the en-
gine and remove it and the cover from the vehicle.
Loosen the hose clamp that secures the factory air intake
tube to the throttlebody. 2. Loosen two hose clamps. One on each side of the
Mass Air Flow (MAF) sensor .
Using a flat blade screwdriver, disconnect the factory
intake tube from the plastic clamp on the radiator hose
by prying them apart. 3. Remove the factory intake tube from the vehicle.
Next, remove the MAF sensor and coupler from the fac-
tory airbox and set them out of the way without discon-
necting the wiring harness.
4. Rock the factory air box back and forth and then lift
straight up remove it from the vehicle. There are only
grommets holding it in, no bolts. 5. Using a 10mm socket, remove the bolts that secure
the factory air filter housing platform and remove it
from the vehicle. 6. Install the filter adapter (#4) into the Cool Air Box
(#3) as shown using three 1/4” Button head bolts (#8)
and three 1/4” flat washers (#11). Next, fasten the brack-
et to the front of the CAB as shown using one 1/4-20
hex bolt (#9) two flat washers (#10), and one 1/4” Ny-
lock nut. Refer to the drawing above for reference.
7. Remove the factory bolt that secures the right front
fender to the radiator support. It will be reused in step
#8. 8. Install the CAB assembly into the vehicle where the
factory airbox used to be using three 6mm hex bolts
(#12) and three flat washers (#11) thru the bottom. Now
reinstall the factory fender bolt thru the bracket and into
the fender. Adjust the assembly for fit and tighten all
bolts and nuts at this time. 9. Reinstall the MAF sensor and coupler onto the filter
adapter and tighten the clamp.
Next install the hump hose (#5) onto the MAF using two
#60 hose clamps (#13). Leave these two clamps loose
for now.
MAF Sensor
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.