Comtech EF Data MIDAS Version 4.X NMS Configuration User Manual
Page 109
MIDAS 4.X NMS Configuration Rev.6
Reports
Menu
3–7
C
C
o
o
n
n
t
t
r
r
o
o
l
l
C
C
h
h
a
a
n
n
n
n
e
e
l
l
S
S
t
t
a
a
t
t
i
i
s
s
t
t
i
i
c
c
s
s
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
s
s
S
S
t
t
a
a
t
t
u
u
s
s
P
P
o
o
l
l
l
l
I
I
n
n
t
t
e
e
r
r
v
v
a
a
l
l
Shows the period of delay before the NMS checks the status of online nodes.
An online node is a node that has successfully logged on to the NMS.
M
M
i
i
n
n
i
i
m
m
u
u
m
m
B
B
a
a
c
c
k
k
o
o
f
f
f
f
Displays the minimum number of polls that may occur before a node can re-
send a message to the NMS.
M
M
a
a
x
x
i
i
m
m
u
u
m
m
B
B
a
a
c
c
k
k
o
o
f
f
f
f
Shows the maximum number of polls that may occur before a node can re-
send a message to the NMS.
U
U
p
p
l
l
i
i
n
n
k
k
P
P
o
o
w
w
e
e
r
r
C
C
o
o
n
n
t
t
r
r
o
o
l
l
Indicates whether Uplink Power Control is enabled (YES or NO).
M
M
o
o
n
n
i
i
t
t
o
o
r
r
E
E
b
b
/
/
N
N
0
0
Shows the E
b
/N
o
from the monitor modem.
R
R
e
e
f
f
e
e
r
r
e
e
n
n
c
c
e
e
E
E
b
b
/
/
N
N
0
0
Shows the expected E
b
/N
o
at the monitor modem.
P
P
o
o
l
l
l
l
C
C
o
o
u
u
n
n
t
t
Displays the number of polls sent to nodes on the network out of the specified
control channel.
R
R
X
X
M
M
e
e
s
s
s
s
a
a
g
g
e
e
s
s
Displays the number of messages from remote nodes received by the specified
control channel. Messages such as call setup requests, status information
messages from the nodes, etc., are included.
T
T
X
X
M
M
e
e
s
s
s
s
a
a
g
g
e
e
s
s
Displays the number of messages sent out to nodes on the specified control
channel. This value differs from the POLL COUNT value because the TX
MESSAGES number excludes general timing messages.
R
R
X
X
F
F
a
a
i
i
l
l
u
u
r
r
e
e
s
s
Displays the number of bad messages detected from remote nodes on the
specified control channel. A bad message may be due to a bad CRC in a
received message, invalid message type, or any other type of data corruption.
T
T
X
X
F
F
a
a
i
i
l
l
u
u
r
r
e
e
s
s
Displays the number of times the specified control channel could not send a
message from the NMS, due to hardware problems on the control channel
card.