Comtech EF Data KST-12025 - Manual (Page 117)

KST-12025 Ku-Band Satellite Terminal Remote Control Operation
Rev. 1 A–7
A.4 Status Commands/Responses
Config Status Command:
Response: >add/OS_'cr'
UCF_nnnnn.n'cr'
DCF_nnnnn.n'cr'
RF_xxx'cr'
UCA_nn.n'cr'
DCA_nn.n'cr'
SEL_n'cr''lf']
The converter configuration status command causes a block of data
to be returned by the addressed RFT-1225. The block of data reflects
the current configuration status.
(nnnnn.n = 14000.0 to 14500.0 MHz.)
(nnnnn.n = 10950.0 to 12750.0 MHz.)
(xxx = ON, WRM, or OFF.)
(nn.n = 0 to 25.0 dBm UC Fine Adj.)
(nn.n = 0 to 25.0 dBm DC Fine Adj-31.0 scale.)
(n = 1, 2, 3, or None.)
Fault Status Command:
Response: >add/FS_'cr'
RST_xxx'cr'
UL_xxx'cr'
DL_xxx'cr'
PS5_xxx'cr'
P12_xxx'cr'
HPA_xxx'cr'
LNA_xxx'cr'
ULD_xxx'cr'
USV_xxx'cr'
UVV_xxx'cr'
DLD_xxx'cr'
(See Note)
DCV_xxx'cr' (See Note)
DVV_xxx'cr' (See Note)
ILD_xxx'cr'
ITM_xxx'cr''lf']
This command returns a block of data reflecting the current and
logged faults. Logged faults will be reset when receiving this
command, while current faults can be read on the second request.
xxx = OK or FLT Unit experienced a restart
xxx = OK or FLT Uplink fault
xxx = OK or FLT Downlink fault
xxx = OK or FLT +5V power supply
xxx = OK or FLT +12V power supply
xxx = OK or FLT Power Amp fault
xxx = OK or FLT LNA fault
xxx = OK or FLT UC LO Lock Detect
xxx = OK or FLT UC LO Vt-S Tuning voltage
xxx = OK or FLT UC LO Vt-V Tuning voltage
xxx = OK or FLT DC Lock Detect
xxx = OK or FLT DC LO Vt-C tuning voltage
xxx = OK or FLT DC LO Vt-V tuning voltage
xxx = OK or FLT IF LO Lock Detect
xxx = OK or FLT IF LO Tuning voltage
Note: In a single synthesizer configuration, these items will display
'DLD_N/A', 'DCV_N/A', and 'DVV_N/A', respectively.
Summary
Fault Command:
Response: >add/SF_xxx'cr''lf'] Where: xxx = OK or FLT.
Returns status of current faults only.
Maint Status Command:
Response: >add/MS_'cr'
UCT_nn'cr'
DCT_nn'cr'
HPT_nn'cr'
USV_nn.n'cr'
UVV_nn.n'cr'
DCV_nn.n'cr'
(See Note)
DVV_nn.n'cr' (See Note)
TIV_nn.n'cr'
VDD_nn.n’cr’'lf']
This command returns a block of data from the RFT-1225 reflecting
the status of certain internal parameters for the purpose of
troubleshooting.
nn = UC temperature in degrees C
nn = DC temperature in degrees C
nn = Power Amp temp in degrees C
nn.n = UC LO Vt-S Tuning voltage
nn.n = UC LO Vt-V Tuning voltage
nn.n = DC LO Vt-C Tuning voltage
nn.n = DC LO Vt-V Tuning voltage
nn.n = Tuning voltage of IF LO
nn.n = Tuning voltage of HPA drain
Note: In a single synthesizer configuration, these items will display
'DCV_N/A' and 'DVV_N/A', respectively.