Bronkhorst EL-FLOW Base 2014 - Manual (Page 21)

BRONKHORST HIGH-TECH
RespStable Unsigned char RW  0x0E51 0x0E52 3666
RespOpen0 Unsigned char RW  0x0E52 0x0E53 3667
Calibration mode Unsigned char RW  0x0E61 0x0E62 3682
Monitor mode Unsigned char RW  0x0E62 0x0E63 3683
Reset Unsigned char W 0x0E68 0x0E69 3689
Sensor zero potmeter Unsigned char RW  0x0E85 0x0E86 3718
Modbus slave addr. Unsigned char RW  0x0FAA 0x0FAB 4011
Polycnst A Float RW  0x8128..0x8129 0x8129..0x812A 33065..33066
Polycnst B Float RW  0x8130..0x8131 0x8131..0x8132 33073..33074
Polycnst C Float RW  0x8138..0x8139 0x8139..0x81A 33081..33082
Polycnst D Float RW  0x8140..0x8141 0x8141..0x8142 33089..33090
TdsDn Float RW  0x8158..0x8159 0x8159..0x815A 33113..33114
TdsUp Float RW  0x8160..0x8161 0x8161..0x8162 33121..33122
Capacity Float RW  0x8168..0x8169 0x8169..0x816A 33129..33130
Fluid name String (10 bytes) RW  0x8188..0x818C 0x8189..0x818D 33161..33165
Capacity unit string String (7 bytes) RW  0x81F8..0x81FB 0x81F9..0x81FC 33273..33276
Fmeasure Float R 0xA100..0xA101 0xA101..0xA102 41217..41218
Fsetpoint Float RW 0xA118..0xA119 0xA119..0xA11A 41241..41242
Temperature Float R 0xA138..0xA139 0xA139..0xA13A 41273..41274
Capacity 0% Float RW  0xA1B0..0xA1B1 0xA1B1..0xA1B2 41393..41394
Device type String (6 bytes) R 0xF108..0xF10A 0xF109..0xF10B 61705..61707
Model number String (14 bytes) RW  0xF110..0xF116 0xF111..0xF117 61713..61719
Serial number String (16 bytes) RW  0xF118..0xF11F 0xF119..0xF120 61721..61728
Manufacturer config String (16 bytes) RW  0xF120..0xF127 0xF121..0xF128 61729..61736
Firmware version String (5 bytes) R 0xF128..0xF12A 0xF129..0xF12B 61737..61739
Usertag String (13 bytes) RW 0xF130..0xF136 0xF131..0xF137 61745..61751
IOStatus Unsigned char RW  0xF258..0xF259 0xF259..0xF25A 62041..62042
PID Kp Float RW  0xF2A8..0xF2A9 0xF2A9..0xF2AA 62121..62122
PID Ti Float RW  0xF2B0..0xF2B1 0xF2B1..0xF2B2 62129..62130
PID Td Float RW  0xF2B8..0xF2B9 0xF2B9..0xF2BA 62137..62138
Kspeed Float RW 0xF2F0..0xF2F1 0xF2F1..0xF2F2 62193..62194
Dynamic displ. factor Float RW  0xF508..0xF509 0xF509..0xF50A 62729..62730
Static displ. factor Float RW  0xF510..0xF511 0xF511..0xF512 62737..62738
Exp. Smoothing filt. Float RW  0xF520..0xF521 0xF521..0xF522 62753..62754
Modbus baud rate Long integer RW  0xFD48..0xFD49 0xFD49..0xFD4A 64841..64842
Notes:
• Access indicates whether parameter can be Read and/or Written.
• When a byte parameter is read, the upper 8-bits of the Modbus register will be 0. When a byte
parameter is written, the upper 8-bits must be set to 0.
• Long integer parameters have a length of 4 bytes and are mapped on two consecutive Modbus
registers. The first register contains bit 32-16, the second register contains bit 15-0.
• Floating point parameters have a length of 4 bytes and are mapped on two consecutive Modbus
registers. Floats are in single precision IEEE format (1 sign bit, 8 bits exponent and 23 bits fraction).
The first register contains bit 32-16, the second register contains bit 15-0.
• String parameters can have a length of maximal 16 bytes and can take up to 8 Modbus registers
where each register contains two characters (bytes). The upper byte of the first register contains the
first character of the string. When writing strings, the write action should always start from the first
register as a complete block (it is not possible to write a part of a string). If the string is shorter than
the specified maximum length the string should be terminated with a 0.
9.17.061 EL-FLOW Base Series Mass Flow Controllers Page 21