Braeburn 5300 2H-2C User Manual - Manual (Page 7)

13
2
PROGRAMMING
USER SETTINGS
cont.
12
Commercial
1. Press the PROG button to enter the Program setting mode.
Press the
SYSTEM button to select HEAT to set heating times and
temperatures. OCCUPIED setpoint of the “Whole Week” will be
displayed. The display will show MO, TU, WE, TH, FR, SA, SU to
indicate the whole week is being programmed. The hour portion
of the setpoint time and the
AM/PM indicator will be flashing.
2. If you wish to program each day individually press the DAY/TIME button to select each day.
3. Press the or button to change the time to the desired hour in one hour increments. Press the PROG
button, the minute portion of the setpoint time will begin flashing.
4. Press the or button to change the time to the desired minute in 10-minute increments. Press the
PROG button, the SET temperature will begin flashing.
5. Press the or button to change the setpoint temperature to the desired setting in 1º F increments
(0.5º C). Press the
PROG button, the FAN mode will begin flashing.
NOTE: The fan option is not available or displayed if the Fan LOCK was enabled during Installer Setup, see the
Installer Guide.
6. Press the or button to select AUTO or ON. Press the PROG button, the thermostat will now display
the
DAY setpoint time and temperature. Again, you will see the hour portion of the setpoint time and the AM/PM
indicator will be flashing.
7. Follow steps 3 through 6 to set the setpoint times and temperatures and fan mode for UNOCCUPIED for the
HEAT mode.
8. Press the SYSTEM button to select COOL to set cooling times and temperatures. The display will show COOL.
Follow steps 3 through 7 to set the setpoint times and temperatures and fan mode for the
COOL mode.
9. Press the RETURN button to return to the normal mode, or wait 30 seconds for the thermostat to
return automatically.
2
PROGRAMMING
USER SETTINGS cont.
2.5.2 Entering Your Program – 5-2 Day Mode (Residential)
The 5-2 Day mode has separate Weekday and Weekend Program Groups that allow you to change the daily
setpoint times and temperatures to meet your individual schedule needs.
Weekday – allows you to program all the weekdays (MO, TU, WE, TH, FR will show in display) at the same time.
Allows programming times and temperature settings for four setpoints (MORN, DAY, EVE & NIGHT) to meet your
weekday schedule needs.
Weekend – allows you to program all the weekend days (SA, SU will show in display) at the same time. Again
allows programming times and temperature settings for four setpoints (MORN, DAY, EVE & NIGHT) to meet your
weekend schedule needs.
1. Press the PROG button to enter the Program setting mode.
Press the
SYSTEM button to select HEAT to set heating times
and temperatures. MORN setpoint of the Weekday Program Group
will be displayed. The display will show MO, TU, WE, TH, FR to
indicate the Weekday group is being programmed. The hour
portion of the setpoint time and the
AM/PM indicator will
be flashing.
2. Press the or button to change the time to the desired hour in one hour increments. Press the PROG
button, the minute portion of the setpoint time will begin flashing.
3. Press the or button to change the time to the desired minute in 10-minute increments. Press the
PROG button, the
SET temperature will begin flashing.
4. Press the or button to change the setpoint temperature to the desired setting in 1º F increments
(0.5º C). Press the
PROG button, the FAN mode will begin flashing.
NOTE:
The fan option is not available or displayed if the Fan LOCK was enabled during Installer Setup, see the
Installer Guide.
SYSTEM FAN
HEAT
AUTO
AM
SET
MOTUWETHFR
MORN
SYSTEM FAN
HEAT
AUTO
AM
SET
MOTUWETHFR SASU
OCCUPIED