Panasonic OMNIVISION PV-S9670 - Manual (Page 21)

•Important: If the remote control POWER, ACTION, PROG, CHA/v, INDEX/ M/A SKIP, NUMBERED keys,
INPUT, TAPE POSITION, or ADD/DLT button does not work when pressed, press the VCR button
on the remote and try the button again.
0
^
Check list before you begin.
Q The clock is set.
□ VCR Plus+ System Setup is complete (see pages 18-20).
Display SET PROGRAM.
Press PROG.
2
.......... SET PROGRAM --------
VCR Plus+ PROGRAM
TIMER PROGRAM
SELECT
SET
END
* ▼ KEY
► KEY
PROG KEY
Display VCR Plus-i-
screen.
1 ) Press AT
to select.
2) Press ►
to display.
3
5
VCR Plus+
ENTER PLUSCODE NUMBER
\ I /
/ I \
USING 0-9 KEYS
To make corrections,
press A repeatedly to delete the
PlusCode programming number.
Enter PlusCode
programming number.
1) Press
Numbered
keys.
2) Press PROG
to lock in the
program.
О © ©
0 © 0
О © ®
©
VCR Plus+
1 ONE TIME
2 DAILY(MON-FRI)
3 WEEKLY
TO SELECT PUSH 1,2 OR 3
Enter record frequency.
3) Press 1,2, or
3 key to select
program type.'
4
DATE START STOP
8 SAT 10:00P 12:00P 02
TODAY \ I /
CATEGORY:N/A
............ -/-f-V-
SELECT CATEGORY
SELECT:* T KEY
SET ► KEY
END ;PROG/ACTION KEY
Select Category.**
1) Press AT to
change.
2) Press ► set.
Change record speed.
Repeat 1) and 2).
Make notes. —> Do step 4 on page 16.
• If not wanted, go to step 6.
6
P DT START STOP OH SPD
1 DAY 9:00A12:00A 08 SP
к»;ШДГ|МА1Д|1«|!Ш|У.ЖТЗ
3 --------- :---------- __ __
4 --------- ;---------- __ __
CANCEL;ADD/DLT KEY
SELECT 1 - 8 ; *
T
KEY
ENTER :► KEY
END :PROG/ACTION KEY
End programming.
1) Press PROG
(or ACTION).
To cancel,
press ADD/DLT.
2) Press PROG
(or ACTION)
again to exit.
If start time of programs overlap,
these programs will flash.
Set timer.
Press POWER OFF.
riffP
Process of Recording
Setup i=>
CD ©
О © ©
© © ©^
© ©
^ TAPE ^
О C__J O!
SPEE&
О
S/WH-R
0
о Qi
a®
7 POWER
SELECT/
SET
A:PLAY
T :STOP
◄ :REW
► ;FF
PROG
0 ACTION
q NUMBERED
keys
ADD/
DELETE
** Category Items
N/A(not applicable), SPORTS,
MOVIE, COMEDY, MUSIC. DRAMA
Use nonnal Timer Recording steps if:
• the PlusCode programming number for a
program is not listed.
• you anticipate the program, such as a sporting
event, to run over the scheduled stop time.
See page 17 to:
• cancel a timer recording in progress.
• replace program contents.
• review or clear program contents once set.
Important notes for DSS/Cable Box users
• When recording via DSS, the receiver,
must be left on,
• When recording via cable or antenna, DSS
receiver must be off.
Multi Function Display
Avoid overlapping program times.
VCR PlusCode programming numbers
can not be used to program the VCR to
record DSS channels.
21