Rice Lake SURVIVOR SST3 Washdown Printer - Manual (Page 48)

Specifications 45
6.0 Specifications
Printing
Type Direct thermal or optional thermal
transfer
Print Speed 2" – 10" per second (51mm – 152mm)
in.5” programmable increments
Resolution 203 dpi (8 dots/mm)
Resident Fonts Ten alphanumeric fonts from 0.03" H –
0.25" H (0.9mm – 6.26mm) including
OCR-A, OCR-B (size and character
set III), and a CG Triumvirate smooth
font from AGFA
Downloadable Fonts True-Type, AGFA Intellifont, Bitmap
Font Expansion All fonts expandable vertically and
horizontally up to 24x; fonts and
graphics can be printed in four
directions: 0
º , 90 º , 180 º , and 270 º
Bar Codes Code 3 of 9, UPC-A, UPC-E,
Interleaved 2 of 5, Code 128, EAN-8,
EAN-13, HIBC, Codabar, Plessey,
UPC 2 and 5 digit addendums, Code
93, Postnet, UCC/EAN Code 128,
Telepen, UPS MaxiCode, FIM,
PDF417, USD-8, Datamatrix, QR
Code, Aztec, TLC 39, Micro PDF417,
RSS
Media
Width 1.0" – 4.65" (25.4mm – 118mm)
Length 0.25" – 99" (6.35mm – 2514.6mm) at
100 dots per inch
Thickness 0.0025" –.010” (0.0635mm –
0.254mm)
Type Roll-fed or fan fold materials, die cut or
continuous labels; perforated or
continuous tag/ticket stock
Supply Roll Capacity 8" (203mm) maximum outside
diameter on a 3" (76mm) core.
7" (178mm) maximum outside
diameter on a 1.5" (38mm) core.
Fanfold stock accepted from rear and
bottom of printer.
Media Supply Solid metal hanger
Media Sensing “See through” for liner backed die cut
labels and tags. Reflective sensor for
black mark label media.
Thermal Transfer
Ribbon
Black or colored inks; 360 meters
long, 4.6 microns, backcoated, ±10%
label width. 1968 feet (600 meters)
max
Switches
Switches CANCEL, PAUSE, and FEED. Variable
Head Temperature Control
Communications Interfacing
Parallel and IEEE
RS-232C 2400, 4800, 9600, 19.2K, 28,800, or
38.4K baud
USB
Wireless
Character Set
ANSI ASCII character set.
Word Length Selectable 7 or 8 bit data format
Handshaking XON/XOFF (on receive mode only) and
CTS/DTR
Input Buffer Approximately 7000 bytes; XOFF is
transmitted and DTR goes low when
60 bytes are available in the buffer.
XON is transmitted and DTR goes high
when 1000 bytes are left in the buffer
Characters transmitted with no parity from the printer
Electrical
Input Voltage 103.5 - 126.5 or 207 - 253 VAC,
47 -63 Hz - Must use appropriate
heater and power cord for voltage
used
Note: The GFI socket outlet should be installed near the
equipment and be easily accessible
Heater Circuit Protection At 115V = 2.0A Fastact
230V = 1.0A Fastact
Grounding Unit must be connected to a properly
grounded receptacle
Power Consumption 90 watts (standby - 10 watts)
UL Listed (pending) Type 4X for indoor use only - NEMA
4X, IP66, IP69K
Memory Modules
Internal Memory
Module
FONT/FLASH modules
PCB without fonts 4 MB addressable
Font Modules
Font Modules Eight available
Range of Fonts ILPC, Kanji Simplified Chinese and I/O
Expansion Board
Environmental
Operating
Temperature
40°F – 95°F (4°C – 35°C)
Humidity 10% – 95% non-condensing
Ventilation Free air movement
Dust Nonconducting, non-corrosive
Electromagnetic
Radiation
Moderate RF fields can be tolerated
Mechanical
Size 27-1/8”L x 14” W x 13-5/8” H
Weight Approximately (65-70 lbs)