Cabletron Systems Smart 04-0053-01 User Manual
Page 79
SmartSwitch ATM User Guide 5-13
Virtual Ports and Static Connections
Soft PVC and PVP Connections
1.
Define a target ATM address to be used on the target switch. The target ATM address can be any
address that is either eight (8) or twenty (20) bytes long and must not be identical to any address
currently listed in the ATM routing table. Use the
show atmroute
command to check which
addresses are currently defined.
SmartSwitch # show atmroute
Num(ALL) :
Num Port Number ATM Address Type Proto
================================================================================
1 -- 39:00:00:00:00:00:00:00:00:00:14:41:80 I PNNI
2 -- 39:00:00:00:00:00:00:00:00:00:28:8d:00 I PNNI
3 -- 39:00:00:00:00:00:00:00:00:00:28:c1:80 I PNNI
4 -- 39:00:00:00:00:00:00:00:00:00:29:05:00 I PNNI
5 CPU 39:00:00:00:00:00:00:00:00:00:a3:87:0b:00:00:1d:a3:87:0b I MGMT
6 CPU 39:00:00:00:00:00:00:00:00:00:a3:87:0b:00:00:1d:a3:87:0b I MGMT
7 CPU 39:00:00:00:00:00:00:00:00:00:a3:87:0b:00:00:1d:a3:87:0b I MGMT
8 CPU 39:00:00:00:00:00:00:00:00:00:a3:87:0b:00:20:d4:34:77:81 I MGMT
9 -- 39:00:00:00:00:00:00:00:00:00:a3:87:0b:00:20:d4:34:77:ff I MGMT
10 -- 39:00:00:00:00:00:00:00:00:00:bf:ba:26 I PNNI
11 CPU 47:00:79:00:00:00:00:00:00:00:00:00:00:00:a0:3e:00:00:01 I MGMT
12 -- 47:00:79:00:00:00:00:00:00:00:00:00:00:00:a0:3e:00:00:01 I PNNI
13 CPU c5:00:79:00:00:00:00:00:00:00:00:00:00:00:a0:3e:00:00:01 I MGMT
14 -- c5:00:79:00:00:00:00:00:00:00:00:00:00:00:a0:3e:00:00:01 I PNNI
SmartSwitch #
2.
Use the
add spvcaddress
command on the target switch to specify the target port and ATM address.
SmartSwitch # add spvcaddress
PortNumber() : 6b3
— Port on target switch
AtmAddress() : 22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22
Added SPVC Address successfully.
SmartSwitch #
3.
Use the
show spvcaddress
command to see the soft PVC port and ATM address on the target switch:
SmartSwitch # show spvcaddress
PortNumber(ALL) :
TargetAddress() :
Port SPVC Target Address
================================================================================
6B3 22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22
Total number of SPVC Addresses = 1
SmartSwitch #
4.
On the source switch, use the
add trafficdescriptor
command to create traffic descriptors for the
forward and reverse directions of the connection (See Section 6.1.1for information about traffic
descriptors).