Great Plains YP825A Operator Manual User Manual
Operator manual, Manufacturing, inc
This manual is related to the following products:
Table of contents
Document Outline
- Operator Manual
- Table of Contents
- Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Be Familiar with Safety Decals
- Wear Protective Equipment
- Avoid High Pressure Fluids
- Keep Riders Off Machinery
- Use Safety Lights and Devices
- Transport Machinery Safely
- Handle Chemicals Properly
- Shutdown and Storage
- Tire Safety
- Practice Safe Maintenance
- Safety At All Times
- Safety Decals
- Safety Reflectors and Decals
- 818-055C Slow Moving Vehicle Reflector
- 838-266C Red Reflectors
- 838-265C Amber Reflectors
- 838-267C Daytime Reflectors
- 818-323C Danger: Possible Chemical Hazard
- 61848 Warning: Tank Hazards
- 818-337C Warning: Speed
- 818-339C Warning: High Pressure Fluid Hazard
- 818-525C Warning: Sharp Object (Option)
- 818-682C Warning: Markers (Option)
- 838-363C Warning: Moving Parts Hazard (Option)
- 818-587C Caution: Read Operator’s Manual
- 848-048C Caution: Tire Pressure and Bolt Torque
- Introduction
- Preparation and Setup
- Operating Instructions
- Pre-Start Checklist
- Raising/Lowering Planter
- Transport
- Loading Materials
- Dry Fertilizer Operation
- Liquid Fertilizer Operation (Option)
- Monitor Operation
- Air System Operation
- Air-Pro® Meter Operation
- Marker Operation (Option) SN+
- Marker Operation (Option) SN-
- Field Set-Up Checklists
- Field Operation
- Short-Term Parking
- Long-Term Storage
- Adjustments
- Setting Material Rates
- Marker Adjustments (Option)
- Fan and Adjustment
- Liquid Fertilizer Adjustments (Option)
- Dry Fertilizer Adjustments (Option)
- Row Implement Adjustments
- 25AP Series Row Unit Adjustments
- Troubleshooting
- Maintenance and Lubrication
- Maintenance
- Material Clean-Out
- Meter Brush Maintenance
- Speed Sensor Gap
- Hydraulic Maintenance
- Drive-Line Shear Pin
- Marker Maintenance (Option)
- Chain Maintenance
- Spreaders and Scrapers
- Row-Unit Side Wheels
- Seed Flap Replacement
- Lubrication
- Opener Side Wheel Bushing
- Chain: Contact Drive
- Chains: Liquid Fertilizer Drive (Option)
- Chains: Dry Fertilizer Drive (Option)
- Chains: Meter Drive
- Chain: Range Drive
- Chain: Transmission Drive
- Gauge Wheel Module Forward Pivot
- Fertilizer Pump Bearings (Option)
- Fertilizer Pump Crankshaft (Option)
- Markers (Option)
- Vantage I Coulter Hubs (Option)
- Vantage I Coulter Pivot (Option)
- Ground Drive Wheel Hub
- Row Cleaner Bearings (Option)
- Gauge Wheel Hubs
- Markers: Disk Hub
- Vantage II: Pivot and Hub
- Seed Lubricants
- Options
- Liquid Fertilizer System
- Dry Fertilizer System
- Dual Sequenced Markers
- Hitches
- Seed Lubricant
- Clean-Out Container
- Frame-Mounted Row Accessories
- Row-Mounted Accessories
- Appendix A - Reference Information
- Specifications and Capacities
- Dimensions 4 Row
- Dimensions 6 Row
- Dimensions 8 Row
- Torque Values Chart
- Tire Inflation Chart
- Plumbing Diagrams
- Hydraulic Diagrams
- Lift Hydraulics
- Fan Hydraulics (YP425A S/N B1008N-) (YP625A S/N B1043Q-) (YP825A S/N B1014S-)
- Fan Hydraulics (YP425A S/N B1009N+) (YP625A S/N B1044Q+) (YP825A S/N B1015S+)
- Marker Hydraulics (Option) (YP425A S/N B1008N-) (YP625A S/N B1043Q-) (YP825A S/N B1014S-)
- Marker Hydraulics (Option) (YP425A S/N B1009N+) (YP625A S/N B1044Q+) (YP825A S/N B1015S+)
- Chain Routing
- See also “Chain Maintenance” on page 107. Ground Drive Arm Chain
- Transfer Shaft and Range Chains
- Transmission Chain (YP425A S/N B1008N-) (YP625A S/N B1043Q-) (YP825A S/N B1014S-)
- Transmission Chain (YP425A S/N B1009N+) (YP625A S/N B1044Q+) (YP825A S/N B1015S+)
- Liquid Fertilizer Drive Chains (YP425A S/N B1008N-) (YP625A S/N B1043Q-) (YP825A S/N B1014S-)
- Liquid Fertilizer Drive Chains (YP425A S/N B1009N+) (YP625A S/N B1044Q+) (YP825A S/N B1015S+)
- Dry Fertilizer Chains
- 25AP Final Meter Drive
- Appendix B - Pre-Delivery
- Appendix C - Initial Setup
- Index